Show complete solutionsFluid mechanics The deepest point in the ocean is 11034m in the Mariana Trench in the Pacific.The average specific weight of seawaterbetween the surface and bottom of thetrench is 10285 N/m^3. If theatmosphericpressure is 101.325 kPa, what is theabsolute pressure in kPa at the bottom ofthe trench? Write youranswer to the nearest whole number.Write only the numerical value of theanswer. Don't write comma if the answeris in thousands. *

Answered: Image /qna-images/answer/25f284a1-89fa-4032-b918-6d312362b577.jpg

Answered: The deepest point in the ocean is 11034…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A block (unit weight = 19.5 kn/m^3) 0.50m square and 382mm deep floats on a stratified liquid composed of 200mm layer of water above a layer of mercury (s.g. = 13.6) If a downward force of 1200 N is applied to the center of mass of this block, what is the new position of the bottom of the block relative to the mercury surface in mm?
What height of a column of a special gage liquid (sp. gr. = 2.95) exert the same pressure as a column of oil 4.5 meters high (sp.gr. = 1.19)? a. 1.58 m b. 1.28 m c. 1.85 m d. 1.82 m
Hi, i have drawn out the question in the attached image. Please calculate and plot the distributions of active and passive pressures on the smooth wall. Soil 1 Soil 2 Cohesion, c 0 0 Bulk Unit Weight 17kN/m3 20kN/m3 angle phi 30 degrees 40 degrees Bulk Unit Weight of water, Yw = 9.81 Please show hand calculations and explain steps. Thankyou !
1. Determine the pressure in Pascal at a depth of 6m below the free surface of a lake.2. What depth of oil (sp. gr. 0.75) will produce a pressure of 275 kPa? What depth of water?
A pressure gage in kPa scale is installed in an underwater submarine. What should be thereading in the gage if the submarine is 100 meters below the surface of the ocean (SG =1.03)? What is the depth of the submarine if the gage reads 1000 kPa?
If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance below the liquid surface, determine the depth to its center of pressure. What is the horizontal force acting on the triangle? Assume ? water = 9790 N/m3. f = depth to apex, 2m d = height of triangle, 1m a = width of triangle, 1m The horizontal force (N) acting on the triangle is:
I'm looking for a conclusion based on this given result from the hydrostatic pressure on plane surface 1. PARTIAL IMMERSION Trials 1 2 3 Total weight on arm M (grams) 50 g 100 g 150 g Depth of Water y (mm) 49 mm 65 mm 80 mm Force on End Surface (experimental) (N) 734.41 N 1512.76 N 2334.59 N Force on End Surface (theoretical) (N) 883,267,875 N 1,554,271,875 N 2,354,400,000 N Depth of Center of Pressure (mm) 16.33 mm 12.67 mm 26.67 mm 2. COMPLETE IMMERSION Trials 1 2 3 Total weight on arm M (grams) 250 g 300 g 450 g Depth of Water y (mm) 109 mm 122 mm 160 mm Force on End Surface (experimental) (N) 4109.31 N 5009.00 N 7704.15 N Force on End Surface (theoretical) (N) 4,340,925,000 N 5,297,400,000 N 8,093,250,000 N Depth of Center of Pressure (mm) 73.12 mm 83.57 mm 117.58 mm
A manometer with diameters L and d is used to measure the pressure difference P1 − P2. Both ends experienceatmospheric pressure. Completely derive the correct expression for the pressure difference:
What is the sea level (g= 32.3 ft/s2) specific weight (lb/ft3) of liquid with density of 58.3 lb/ft3?
Q2) Calculate the value of pressure ∆p onside the rain water droplet , if we knowthe radius R=0.2mm and the surface tensionδ = 0.074 N/M
A vertical conduit is carrying oil (S = 0.95). A differential mercury manometer is tapped into the conduit atpoints A and B. Determine the difference in pressure between A and B when h = 3 in. What is thedifference in piezometric head between A and B?
4. A reservoir supplies water to a horizontal 6′′ pipe 800 ft long. The pipe flows full and discharges into the atmosphere at the rate of 2.23 cfs. What is the pressure in psi midway in the pipe, assuming the only lost head is 6.20 ft in each 100 ft of length? indicaye free body diagram

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS