Q15. Assume a triangular element with nodes Q, R and S at points (X1,Y1), (X2,Y2), and (X3,Y3), respectively.For the needs of the Delaunay triangulation approach, the centre (XC,YC) and radius r of thecircumcircle of the triangle (QRS) are required. Based on the data given in the table below, find thecoordinate YC.X1Y1X2Y2X3Y3215-1

answer is in next step . please give a like

Answered: For the needs of the Delaunay…

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter81: Introduction To Computer Numerical Control (cnc)

Section: Chapter Questions

Problem 4A: A rectangular solid has length L=12.6 mm, width W=23.8 mm, and height H=32.5 mm. Find the length of...

See similar textbooks

Similar questions

use the map in Figure 11.2. a Find the grid section of Taylor Hall. b. What is located in section 3B?
Generalize the results found in Exercise 11 and 12 by answering each of the following questions. Assume that the number of sides in each base of the prism is n. For the prism, what is the a number of vertices? b number of lateral edges? c number of base edges? d total of base of edges? e number of lateral faces? f number of bases? g total number of faces?
If MNPQ is a rhombus, which formula from this section should be used to calculate its area? Exercise 46
A rectangular solid has length L=12.6 mm, width W=23.8 mm, and height H=32.5 mm. Find the length of a diagonal AB from the upper left rear vertex to the lower right front vertex. Round the answer to 1 decimal place.
For Figure a of Exercise 1, find the number of faces, vertices, and edges in the polyhedron. Then verify Eulers equation for that polyhedron.
Given: Hole centerlines EFGH and MPKL. Determine the values of 1 through 15 for these values of 16 .
This sheet metal section shown in Figure 5-5 has five sets of drilled holes: A, B, C, D, and E. The holes within a set are equally spaced in the horizontal direction. Compute the horizontal distance between two consecutive holes for each set. All dimensions are in inches. A=_B=_C=_D=_E=_
Compute dimensions A, B, C, D, and E of the support bracket shown in Figure 191. All dimensions are given in inches. A=_B=_C=_D=_E=_

Recommended textbooks for you

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Elementary Geometry for College Students

Geometry

ISBN:

9781285195698

Author:

Daniel C. Alexander, Geralyn M. Koeberlein

Publisher:

Cengage Learning

PREALGEBRA

Algebra

ISBN:

9781938168994

Author:

OpenStax

Publisher:

OpenStax

SEE MORE TEXTBOOKS

For the needs of the Delaunay triangulation approach, the centre (XC,YC) and radius r of the circumcircle of the triangle (QRS) are required. Based on the data given in the table below, find the coordinate YC.