For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a roughness coefficient of 0.014 L2 Dz Pipe Length, ft Diameter, in 1 980 2 490 Li Di Ls Ds n = 0.014 3 250 980 1480 L3 D3 La D Which of the following statements is TRUE? O The head loss in pipes 1 and 5 are equal. The head loss in pipes 3 and 4 are equal. The headloss in pipe 2, 3 and 4 are equal. The sum of the head loss in pipes 3 and 4 is equal to the head loss of pipe 2. 2345 88851 12 2 points

For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a roughness coefficient of 0.014 L2 Dz Pipe Length, ft Diameter, in 1 980 2 490 Li Di Ls Ds n = 0.014 3 250 980 1480 L3 D3 La D Which of the following statements is TRUE? O The head loss in pipes 1 and 5 are equal. The head loss in pipes 3 and 4 are equal. The headloss in pipe 2, 3 and 4 are equal. The sum of the head loss in pipes 3 and 4 is equal to the head loss of pipe 2. 2345 88851 12 2 points

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows in a 350mm- diameter pipe at the rate of 600 liters per second. The pipe has a length of 64m. Compute the head loss using Darcy Weisbach formula with f=0.028. Compute the head loss using Hazen William’s Formula with C=92. Compute the head loss using Manning’s formula with n=0.012
Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3connected in series with length of 170 m, 300 m, 210 m respectively. Thedifferent in water surface levels in two reservoirs is 12 m. The friction coefficientfor pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based onTable 2 and the setting given, determine the flowrate of the flow if the entranceloss coefficient is 0.25 considering :(i) minor losses; and(ii) neglecting minor losses pipe 1 =230(mm) Pipe 2 =330(mm) Pipe 3 = 430(mm)
Hydraulic structure Q.2: Given the following data of a head regulator: The discharge= 60 cumecs, bed level of the canal-52.2m, crest level of the regulator=52.8m, upstream water level-54.2m, downstream water level=53.9m. The dimension of gates= (2.5x3)m and the thickness of the piers is 0.9m. Neglect the velocity head and use coefficients of discharge= 0.8 and 0.577. Determine the water way of the regulator
In the context of a sewer system, your objective is to find the optimal slope (SS) of a pipe to meet a design flow rate (QdQd) and a maximum allowed flow depth percentage (y/Dy/D). Utilize the flow velocity equation: V = -2 * SQRT(8 * g * R * S) * LOG10((ks / (14.8 * R)) + (2.51 * μ / (4 * ρ * R * SQRT(8 * g * R * S)))Given: Design flow rate (QdQd): 4.12 m³/s Pipe diameter (DD): 1 m Pipe roughness (ksks): 1.50E-06 m Maximum flow depth percentage (y/Dy/D): 85% Fluid density (ρρ): 999.1 kg/m³ Fluid viscosity (μμ): 1.14E-03 Pa·s Acceleration due to gravity (gg): 9.81 m/s²
In the pipeline shown in the figure, the diameter of all pipes (D) is 200 mm and their friction coefficient (f) is 0.02. Thisfor pipeline a) Calculate the maximum flow and draw the hydraulic slope plot. b) Flow rate Q=0.05 m3 To reduce to /s, calculate the required head loss on the valve and calculate the hydraulic slope line.draw. c) HP = 15 – 2000Q2 (Q:m3 /s, Hp: m) placement of a pump with characteristic equation at point BCalculate the flow rate and draw the hydraulic gradient line. Note: The criteria for 3 m < P/γ < 80 m and 0.5 m/s < V < 2 m/s along the pipeline must be met for all cases.
Write legibly Complex Pipeline System_Parallel Pipes 1. The pressure heads at junctions A and E are 70.0 m and 46.0 m, respectively, in the given parallelpipe system shown in the figure. Theflow rate of water entering junction A is 0.30 cms. Assuming that the Hazen – Williams roughness coefficient C = 120 for all pipes, determine the flow rate through each branch of the loop. For the solution, use the Hazen – Williams formula. Answer: a. Pipe ABE = _______________________ cmsb. Pipe ACE = _______________________ cmsc. Pipe ADE = _______________________ cms
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
If the total flow of 4.0m3/? takes place in the three pipes. Determine the distribution offlow. The pipe lengths, diameters and frictions factors are shown below.
Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe
13. Situation 5 - A 0.60 m diameter pipeline 30 m long carries 0.4 m^3/s of water. a. Compute the head loss, in meters, if n = 0.014. Round off to three decimal places. b. Compute the head loss, in meters, if f = 0.014. Round off to three decimal places. c. Compute the head loss, in meters, if C = 140. Round off to three decimal places.
Questions #2 The discharge of the pipe system shown is 0.85 M/sec. The length of pipes 1, 2, 3, 4 and 5 are 1000 m, 500 m ,600 m, 800 m and 700 m, respectively. Pipes 2, 3 and 4 are laid parallel and drawn from pipe 1 and discharge into pipe 5. The diameters of pipes 1, 2, 3 and 5 are 90 cm, 50 cm, 40 cm and 75 cm respectively. The total head loss in the pipe is 10 m. Assuming f=0.02. A. 0.104 B. 0.014 C. 0.410 D. 0.129
Water flows at a rate of 0.8 cumecs in a 900 m-long pipe with a total head loss of 4m.Solve for the pipe diameter in mm by, a.Manning's formula with n = 0.014; and (b) Hazen-Williams formula with C1 = 130.