For the section shown, if a = 200 mm, b = 25 mm, shear flow between the flange and the web is 120 kN/m, the allowable shear stress of the glue is 2 MPa and each nail resist shear of 4.2 kN, then the spacing of the nails is nail glue d 600 mm 35 mm 350 mm 60 mm 365 mm

For the section shown, if a = 200 mm, b = 25 mm, shear flow between the flange and the web is 120 kN/m, the allowable shear stress of the glue is 2 MPa and each nail resist shear of 4.2 kN, then the spacing of the nails is nail glue d 600 mm 35 mm 350 mm 60 mm 365 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Related questions

Q: Situation 11- The force P of magnitude 850 N is applied to the pedal shown in Figure S03-25M (252).…

Q: A free The (M/EI) diagram of a cantilever beam is shown in the Figure. If the deflection of the free…

Q: m REQUIREMENT: PCS- "THICK INTERIOR PLYWOOD WALLS PCS- ¼" THICK EXTERIOR HARDIFLEX WALLS PCS-…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: Q1. 11.3). Determine the moments at the supports A and C, then draw the Moment Diagram Assume joint…

A: FEM - Fixed End Moments ; AB = - wL8 = -25 × 68 = - 18.75 KN-m BA = wL8 = 25 × 68 = 18.75 KN-m BC =…

Q: 1. A force of 250 kN at 25° is combined with a force of 180 kN at 100°. What is the resultant force…

Q: A 1775g of coarse aggregates was soaked for at least 24hours prior to the lab. It is then brought to…

A: weight at ssd = 1800g weight at submerged = 1750g weight after oven drying = 1700g weight of basket…

Q: A is 150 mm and the liquid flows in at the rate of 56 dm3 /s and has a specific gravity of 0.93. At…

Q: P-Green Building features high-efficiency systems the following except: a. Heating b. Lighting c.…

A: In this question we are asked to find out correct option regarding a question from green building…

Q: A circular aluminum tube of length L=500 mm is loaded in compression by forces P (see figure (a)).…

Q: Find the magnitude P of the largest additional vertical force that can be applied to the bar decimal…

Q: A 1775g of coarse aggregates was soaked for at least 24hours prior to the lab. It is then brought to…

Q: If the curve is designed for a two axled truck for extra width w of 0.6,lateral width between the…

A: Given data Extra width (We) = 0.6 B = 1.3 m Length (l) = 7m As width of road is not given, let's…

Q: Why is it that sacks made of woven polypropylene shall not be stacked more than 3 m high? Give at…

A: To create a lightweight, robust, and heavy-duty textile, polypropylene strips or threads are woven…

Q: 1. A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for…

A: The adequacy of a beam is checked in order to evaluate if it is safe for use. There are a number of…

Q: Situation 5 - A 12-m simple beam supports a uniform load of 36 kN/m over 5 m from the left end.…

A: Given: Simply supported beam Loading To find: Maximum bending moment Shear force at mid span…

Q: W 2 ↓ |B -12-

Q: Find all moments Use

A: This frame is non-sway type frame as it has a fixed support at point B that does not allow any…

Q: The beam with three supports carries a uniformly distributed load. Determine all the support…

Q: Analyze the Frame using Portal Method. Disregard the area given of the column. 845 12ft L 10 in MS…

A: Portal Method - It is the approximate method for the analysis of indeterminate frames. Suitable for…

Q: the slope of the beam at E and (b) the deflection of the beam at C.

Q: A circular aluminum tube with a length of L= 420 mm is loaded in compression by forces P (see…

Q: The 36-lb collar shown is released from rest in the position shown. It slides with negligible…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: Slope: The angle which is formed between the deflected beam and the actual beam at the same point…

Q: Situation 2. Design a T-beam for which bw = 300 mm and d = 550 mm. The beams are 4.5 m long and…

Q: A trapezoidal channel has a bottom width of 6 m and side slopes of 2 horizontal to 1 vertical. If…

Q: Considering horizontal reaction at B as redundant, what is the horizontal displacement at B for the…

A: By force method HC is redundant∆HC+F11×HC=0

Q: Ex:-@ Find the END Moment by slope. deflection equation

A: Fixed End Moment:MFAB=MFBA=0MFBC=-wL212=-36×5212=-75 kN.mMFCB=wL212=36×5212=75 kN.mMCD=-36×1×0.5=-18…

Q: In the figure below, the 0.89-in diameter pins at A and C that supports the structure are in single…

Q: Problem 3. For the truss shown, determine the forces in members AB, BD, AD and CD 400 lb. 200 lb C

A: Given the above truss. Using method of sections and method of joints, the forces in the unknown…

Q: What are verious types of failures in cement concrete pavements? Explain their causes with sketches,…

A: Rigid pavements are those which are made up of cement concrete slabs. The load is transferred to…

Q: 20. The elevation of a tower from two points, one due east of the tower and the other due west of it…

Q: The simply supported beam consists of a W14 × 34 structural steel wide-flange shape [E = 29,000 ksi;…

Q: 1) A truck and trailer combination having the axle loads as shown in the figure rolls across the…

A: Shear Force: The Algebraic sum of all the vertical forces acting on the beam is known as Shear…

Q: In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in…

Q: From the given beam, determine the smallest moment of inertia required so that it's maximum…

A: Given, δmax = L/360 E = 200 GPa

Q: An L= 27-ft-long soldier beam is used as a key component of an earth retention system at an…

Q: A vertical sheet piled wall is shown in Fig. below, the properties of the soil both behind and front…

Q: ". Find the area bounded by the curve y-9-x² and the x-axis. .25 sq.units . 18 sq.units B. 36…

A: Required Area between curve (y = 9-x²) and x axis

Q: Engineering Surveys (Earthworks) A rectangular prism has the following offsets at every corner:…

Q: Minimum shearing stress and maximum torsional stress occur at the center of the circular shaft under…

Q: A uniform horizontal beam, connected to the rigid wall with a pin joint, has a span of 10.0 m and a…

A: Asked: To determine the tension in cable AB and the reaction at pin at C. Given: Mass of beam BC…

Q: 4. From the figure shown, Determine, e. Centroid with respect to x-axis f. Centroid with respect to…

A: *Multiple Sub- parts* As per our company guidelines we are supposed to answer ?️only first 3️⃣…

Q: Tabulate the components and determine the resultant (magnitude and direction) of the given system of…

Q: Find the value of a) (n((-i) bln (3 +√3)

Q: (i) What is moment magnification or second order effec order effects that are generally considered…

A: Moment magnification Second amplification is a worked on approach to representing section slimness…

Q: The simply supported beam consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa;…

Q: In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards.…

A: Given, Tensile working stresses for the plywood =1245psi Tensile working stresses for the boards…

Q: 11. The range of water content between the liquid and plastic limits is termed as: A. liquid limit…

Q: The static level of water table in an unconfined aquifer was 30 m above the underlying impermeable…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

For the section shown, if a = 200 mm,
b = 25 mm, shear flow between the
flange and the web is 120 kN/m, the
allowable shear stress of the glue is 2
MPa and each nail resist shear of 4.2
kN, then the spacing of the nails is
I
K
nail
key
glue
d
600 mm O
35 mm
350 mm
60 mm
365 mm O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two strips of plastic material are bonded together using splice plates as shown. The average shearing stress in the glue must be limited to 1,050 kPa. If P = 45 kN, what splice plate length L is required? a. 142.9 mm b. 149.2 mm c. 192.4 mm d. 124.9 mm
The allowable stresses for the splice shown below are the following: 150 MPa. for shear of rivets, 1.35Fy for bearing, 0.6Fy for tension, and Fy = 250 MPa. Note: rivet holes are 2mm bigger than the rivet diameter, middle plate is 20 mm thick. 1. Find the diameter of rivets so that the joint capacity due to shear approximately equals that due to bearing. a. 25 mm b. 28 mm c. 30 mm d. 36 mm 2. Find the maximum safe P without exceeding the allowable shearing stress. a. 884.4 kN b. 938.3 kN c. 878.1 kN d. 848.2 kN 3. Find the maximum safe P without exceeding the allowable tensile stress. a. 579 kN b. 708 kN c. 495 kN d. 692 kN
Use Method of Joints ABAHBHHGBCBGGCCDGDGFDEFEDF
A square post which is made up of two parts is glued at plane abcd with the angle α = 30° with the vertical. Allowable compressive stress @ glue = 5.2 MPa Allowable shearing stress = 3.5 MPa P = 36 kN. )What is the minimum post dimension, w (mm), without exceeding the allowable compressive stress at the glue? 2.) What is the minimum post dimension, w (mm), without exceeding the allowable shearing stress at the glue? 3.)What angle, α, will give the maximum shearing stress?
The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 11 mm, the length of the plywood is L = 288 mm and the width of the wood is W = 119 mm. Find the shearing stress (in Mpa) in the glue if P = 35.9 kN. Round off the final answer to two decimal places.
A PL ½ x 8 tension member is connected with six 1-inch diameter bolts as shown in the figure below. The steel is ASTM A36. Shear lag factor, u = 1.0. 1. What is the allowable tensile strength (ASD) for yielding? 2. What is the diameter of the hole? 3. What is the ΦPn based on rupture?
The thin uniform plate shown has a mass of 100kg and is subjected to a force and couple momentalong its edges. If it is supported in the horizontalplane by a roller at A, a ball-and-socket joint at B,and a cord at C, determine the components ofreaction at these supports to maintain equilibrium. Please provide all written work and show FBD. Thank you!
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam section 250 mm wide, 400 mm deep is reinforced with 2-36-mm-dia. rebars, grade G420 enclosed with 10-mm-dia. stirrups. X Calculate the tensile steel stress when concrete crushes at a strain of 0.003. Use f'c = 21 MPa. Use 3 Decimal Places.
A nail joint is subject to medium term tensile loading under service class 2. The joint comprises of eight 3.75 x 60 mm long round wire in single shear in C18 timber. What is the slip modulus? Question 4Answer a. 780.38 b. 550.69 c. 625.37 d. 659.19
A steel bar is attached to a wood support beam with four 21 mm diameter lag screws, as shown in the figure. The steel bar is 66-mm-wide by 9-mm-thick. The yield strength of the steel is 265 MPa and the ultimate bearing strength is 345 MPa. For the lag screws, the ultimate shear strength is 160 MPa. If a factor of safety of 1.85 with respect to yield strength, 3.5 with respect to bearing strength, and 2.8 with respect to shear strength is required, determine the allowable load P that can be supported by this connection. For the yield strength criterion, consider the constant cross-section part of the steel bar.
Continuing the solution of the given problem, find the required tie wire in kilograms if the reinforcements are space at: a.Vertical bars spaced at 80 cm and one horizontal bars atevery 3 layers of the block. b.Vertical bars at 60 cm and one horizontal bar at every after2 layers of the block. c.Tie wire in kilograms. (30 cm) Attached are the previous solutions
Shear strength value τ = 200 MPa The contents associated with bolts are given. P = 70 kN required for the safe transfer of the load of value Determine the minimum bolt diameter