For the truss loaded as shown, determine the member forces in BC, CF, and FG in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-8 kN3 kN27 kN3 kN4 mHFG3@3m =9mFecmagnitudekNsensecompressionFCFmagnitudekNsensetensionmagnitudekNsensetensionAlso, identify all zero force members in the truss. (Enter your answers as a comma-separated list.)

Answered: Image /qna-images/answer/c997bb47-bdc2-43dc-9a5a-2cee5a7c2e95.jpg

For the truss loaded as shown, determine the member forces in BC, CF, and FG in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations 8 kN 3 kN 27 kN B 3 kN 4 m H 3@3m =9m Fec magnitude kN sense compression magnitude kN sense tension FEG magnitude kN sense tension

For the truss loaded as shown, determine the member forces in BC, CF, and FG in kilonewtons. Use the method of sections. (Due to the nature of this problem, do not use rounded intermediate values in your calculations 8 kN 3 kN 27 kN B 3 kN 4 m H 3@3m =9m Fec magnitude kN sense compression magnitude kN sense tension FEG magnitude kN sense tension

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem #01: Analyze the given beam using flexibility method. Take moment as redundant on A and B. (CLO-1)E=30000 ksiI=800 in4 0.0015 rad
34 - A support is a fixed, B support is a sliding joint. loads M= 30 kNm, P1= 12 kN, P2= 13 kN, q1= 6 kN ⁄ m, q2= 7 kN ⁄ m , spans are a= 2 m, b= 3 m. The support reactions in the beam whose loading condition is given in the figure will be found. Accordingly, Ax = ?A) 22.25B) 0C) None.D) 39.25E) 21/2
The W8 * 48 cantilevered beam is made of A-36 steel and is subjected to the loading shown. Determine the displacement at C and the slope at A. (Use the principle of supperposition and Appendix C to answer this question). Ix = 184 in4 . E=29000 ksi.
Determine the nominal moment strengt of the irregular beam shown. Assume the area of 25 mm rebar is 510 sq. mm. Given: a.) fc' = 35 MPa; fy= 413.70 MPa b.) fc' = 21 MPa; fy = 413.70 MPa
Use the method of sections. Beam ABCD has a hanger connected at B and is supported by a roller at A and a pin at C. L1 = 202 N/m L2 = 32 N/m L3 = 222 N/m L4 = 97 N/m M = 89 N/m
A beam AB, 1.2m long, is simply-supported at its ends A and Band carries two concentrated loads, one of 10 kN at C, the other 15 kN at D. Point C is 0.4m from A, point D is 1 m from A. Draw the S.F. and B.M. diagrams for the beam inserting principal values.
For the frame loaded as shown, draw the complete and correct FBDs of thefollowing: whole frame, member BE, member HK, pulley D, pulley J, member CDEHJwithout the pulleys, and pin B. If block G weighs 133 N, determine all the forcesacting on member CDEHJ (i.e. Cx, Cy, Dx, Dy, FBE, FHK, Jx and Jy). Also, calculate thehorizontal (ABCBx) and vertical (ABCBy) components of the reactions betweenmember ABC and pin B.
Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C 112.1 C
Answer the problem below, following the GIVEN-REQUIRED-SOLUTION format. Please provide the FBD. Problem: The pin spanner is used to turn shafts and collars. If a moment of is required to turn the 200-mm-diameter collar about its center O under the action of the applied force P, determine the contact force R on the smooth surface at A. Engagement of the pin at B may be considered to occur at the periphery of the collar.
Use the method of sections. Beam ABCD has a hanger connected at B and is supported by aroller at A and a pin at C. Given: L1 = 206N/m L2 = 30N/m L3= 214N/m L4 = 89N/m M = 89N.m
The rectangular beam with a span length of 7.2 m has an effective depth, d = 430mm and a width of 250mm. It has 2-legged 10mmØ stirrups spaced at 130 mm on centers all throughout the beam length. Determine the maximum wu that the beam can carry based on the shear capacity of the beam. Use fc' = 21MPa and Grade 40 rebars. a. Adopt smaller of S' : S'1 = Avfy / (0.062b√f'c) S'2 = Avfy / (0.35b) b. S" = (0.062/0.33) / S'1 c. 1. if S > S' ; ØVn = Ø 0.5Vc 2. if S"<S<S' ; Smax = least of S' or d/2 or 600mm i. S> Smax ; ØVn = Ø 0.5Vc ii. S< Smax ; ØVn = Ø (Vc + ( Avfyd / S ) ) 3. if S < S" ; Smax = least of S' or d/4 or 300mm i. S> Smax ; Vs = 0.33√f'c bwd ØVn = Ø (Vc + 0.33√f'c bwd) ii. S< Smax ; ØVn = Ø (Vc + ( Avfyd / S ) ) Find: 1. Vc 2. s' and s'' 3. smax 4. ØVn 5. Wu
s shown in the sketch, an interior column AB in a steel frame carries a factored axialcompressive load, Pu = 1540 kips. The column is braced at the top and bottom and the mid-height in the perpendicular plane, and sidesway in the plane of the steel frame is allowed. Thecolumns are 12-ft long, and the columns above and below the column AB are the same size asAB. The adjacent girders are W 18×50 and are 32-ft long. Use A992 steel with Fy = 50 ksi,select the lightest W-section for the column AB. Use stiffness reduction factor where applicable.