For the truss shown below determine the member forces in BC, CI, and IJ in kilonewtons. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-B3 mM1.284 kN 1.070 kN856 N642 N428 N214 N6@1.5 m = 9 mFBCmagnitudekNsensetensionFCImagnitudekNsensecompressionIJmagnitudekNsensecompression

Answered: Image /qna-images/answer/161a863c-f4b1-4603-b853-6cbcfe5cea83.jpg

For the truss shown below determine the member forces in BC, CI, and IJ in kilonewtons. (Due to the nature of this problem, do not use rounded intermediate values in your calculations- 3 m E H. K L. M 1.284 kN 1.070 kN 856N 642 N 428 N 214 N 6@1.5 m = 9 m FBC magnitude KN sense tension FCI magnitude kN compression sense F, magnitude kN sense compression

For the truss shown below determine the member forces in BC, CI, and IJ in kilonewtons. (Due to the nature of this problem, do not use rounded intermediate values in your calculations- 3 m E H. K L. M 1.284 kN 1.070 kN 856N 642 N 428 N 214 N 6@1.5 m = 9 m FBC magnitude KN sense tension FCI magnitude kN compression sense F, magnitude kN sense compression

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A wide flange section is used as beam to support a concrete floor system. The beam is simply supported over a span of 6m. The properties of the section are given as follows:Depth, d = 498mmWeb thickness, tw = 56mmMoment of Inertia about x-axis, Ix = 3417 x 106 mm4Section Modulus about x-axis, Sx = 13730 x 103 mm3Self-weight, wself-weight = 7.32 kN/mAssume the beam is laterally supported over its length with its allowable stress in bending is 0.66Fy and its allowable shear stress is 0.40Fy assuming direct shear stress is used as basis instead of flexural shear stress. The allowable deflection is set at L/360. Use A36 steel with Fy = 250 MPa. (a) Compute for the safe uniform load (w) without exceeding the allowable shear stress. (b) Compute for the safe uniform load (w) without exceeding the allowable bending stress. (c) Compute for the safe uniform load (w) without exceeding the allowable deflection.
The length of the 3/32 in.diameter steel wire CD has been adjusted so that with no load applied, a gap of 1/16 in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=29 X 10⁶ psi, determine where a 50-lb block should be placed on the beam in order to cause contact between B and E.
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
A force of F = {6i - 2j + 1k} kN produces amoment of MO = {4i + 5j - 14k} kN ⋅ m about the origin,point O. If the force acts at a point having an x coordinateof x = 1 m, determine the y and z coordinates. Note: Thefigure shows F and MO in an arbitrary position.
39. Bending moment equation of section BC. O a. 26KN(x)+56KN.m O b. 26KN(x)-56KN.m O c.-26KN(x)+56KN.m O d. None of the above. 40.Maximum bending moment of the beam. a. 47KN.m b.46KN.m d. None of the above These are related questions
Compute all reactiosn for the beam in FigureP9.15 assuming that the supports do not move; EI is constant. (b) Repeat computations given that support C moves upward a distance of 288/EI when the load is appleid
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations.) Ax=0 Ay=? By=? Magnitude and direction
Given P1=00K P2=19K UNKNOWN: 1. FORCE IN MEMBER GF 2. FORCE IN MEMBER FC 3. FORCE IN MEMBER CD
5. What is the approximate moment at support a? In kN.m A. -79.86 B. -27.95 C. -73.28 D. 0 E. -10.98 F. 73.28 G. 79.86 H. 10.98 I. 27.95
For the truss shown , The strength of the truss is assumed to be governed by the strength of member BC. Use Fy = 248 MPa and E = 200 GPa. The member BC is composed of two angular sections placed back-to-back separated by s = 8 mm as shown. If a = 4 meters,Properties of 75 x 75 x 12 mm angleA = 1774 mm²Ix = 0.92 x 10^6 mm^4Iy = 0.92 x 10^6 mm^4x = y = 23.25 mm 1. Using LRFD, which of the ff. most nearly gives the value of P in kiloNewtons. 2.Using LRFD, which of the ff. most nearly gives the reaction at D kiloNewtons. 3. Using ASD, which of the ff. most nearly gives the design strength of member BC in kiloNewtons.
18. The beam which is supported by hinge and roller at its ends, is called as a. simple supported beam b. continuous beam c. propped beam d. cantilever beam 19. Which of the following is statically determinate beam? a. simply supported beam b. cantilever beam c. overhanging beam d. all of these 20. Which quantity does not affect Shear Force Diagram? a. Point load b. Uniformly distributed load c. Uniformly varying load d. Couple
Situation 2. Refer to FIG DENJIRO. Neglect the thickness of the member. 3. Determine the moment of the force about point O in N-m. a. 18.32 b. 2.41 c. 14.66 d. 11.25 4. Determine the distance of the 50 N load from point O in mm. a. 224.97 b. 293.19 c. 48.236 d. 366.39