From the diode circuit shown below, If E=40 V and RL=800, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 Q. D. D2 RL www D4 D3 a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is

From the diode circuit shown below, If E=40 V and RL=800, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 Q. D. D2 RL www D4 D3 a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
How is a solid-state diode tested? Explain.
A diode is doped with NA = 1018/cm3 on the p-type side and ND =1019/cm3 on the n-type side. (a)What is the depletion-layer width wdo? (b) What are the values of xp and xn? (c) What is the value of the built-inpotential of the junction?(d) What is the value of EMAX? Use Eq. E(x) = 1 /εs ∫ ρc(x) dxand as shown.
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
Since R1=4.51 Kohm, R2=1.19 Kohm R3=2.74Kohm R4=5.60Kohm VCC=23.00V and diode silicon in the circuit given in the figure, find the current passing through the diode in mA
Which of the following indicates the correct rms value of the diode current for a 1-0 full bridge diode rectifier supplied by a source voltage of 220 V, 60 Hz? The value of load resistance is 2012 (assuming large inductance for maintain constant load current). (a) 9.90 A (b) 7.0 A (C) 4.95 A (d) 11 A COMPANY
A 1N4738A zener diode has a ZZ of 4.5 Ω. Taking the data from the datasheet we have VZ = 8.2 V with a test current, IZ, of 31 mA. What is the voltage across the zener terminals when the current is 15 mA? When the current is 55 mA? Make the representation of the values by means of their curve characteristic.
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
Assume D = D0e^–Ea/kT is the diffusion coefficient of boron in silicon surface, whereD0 = 10.5 cm^2/s and Ea = 3.7 eV. The substrate is N-type silicon doped to 10^15 cm^3.N0 = 10^15 cm^2 of boron is introduced just below the silicon surface.(a) What is the junction depth after a 1-h drive-in at 1,100°C?(b) By how much will the junction depth change after 10^6 h (~100 years) of operation at100°C
Find the value of dc and ac resistance of a Germanium junction diode if the temperature is 25 degree Celcius, Reverse Saturation Current is 20 microAmperes and applied voltage of 0.1V. a.) rDC= 75.6 ohms, rAC=11.2 ohms b.) rDC= 120.7 ohms, rAC= 28.4 ohms c.) rDC= 95.1 ohms, rAC=12.3 ohms d.) rDC= 109.2 ohms, rAC=26.3 ohms
Question 3 a) The Fermi level of a solid-state body is the thermodynamic work required to add one electron to the body. The Fermi level does not include the work required to remove the electron from wherever it came from. With the aid of diagram discuss the importance of the Fermi Energy level, especially its relevance to electron flow in a pn-junction diode. b) Discuss the I/V characteristics curve of a practical Germanium diode and explain in detail how the forward and reverse are achieved. Support your explanation with a suitable circuit diagram with a voltage source and RC components connected across the p-n junction
The concentration of donor impurity atoms in silicon is Nd = 1015 cm-3. Assume an electron mobility of u, = 1300 cm?/V-s and a hole mobility of u, = 450 cm2/V-s. (a) Calculate the resistivity of the material. (b) What is the conductivity of the material?