G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm? 4m E=200Mpa A D Aluminum L=2m A=500mm 2m 2m E=72Mpa P=20KN

G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm? 4m E=200Mpa A D Aluminum L=2m A=500mm 2m 2m E=72Mpa P=20KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
Q-1 The factor of safety for a machine element depends on the particular point selected for analysis. For the bar and loading, shown in figure below, we need to have a minimum factor of safety, ηy = 2.5. The bar is to be made of AISI 1050 cold-drawn steel and is loaded by F = 2.65 kN, P = 10.5 kN, and T = 52 N-m. a). Draw planar stress elements (A and B) showing normal and shear stresses at their proper orientations. b). Determine a safe diameter d to the nearest mm, based upon the distortion-energy theory, for both stress elements at A and B of the member shown in the figure. c). Determine the safe diameter, d, based on maximum shear stress theory. d). You are the designer, and you are to decide on the safe diameter, chosen from one of the diameters obtained from different failure theories used in parts (b) and (c) above, and explain your final decision made on the diameter.
The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine: The stress in each cable. Answ: 25.09 MPa, 49.22 MPa. The vertical displacement of the beam. Answ: 1.99E-3 m.
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.
The shaft is made from a solid steel section AB and a tubular portion made of steel having a brass core. It is fixed at a rigid support at A and a torque T=50lb-ft is applied at C. Gsteel= 11,500 ksi Gbrass= 5,600 ksi What is the angle of twist at C? What is the maximum shear stress in the steel and brass? What is the maximum shear strain in the steel and brass?
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the normal stress in rod (1). Express your answer in MPa rounded to the nearest hundredths.
The bar of the pin connected frame shown are each 30mm by 60mm in section. determine the maximum load P that can be applied so that the stress will not exceed 100MN/me in tension or 80 MN/me in compression
GI, GE, and GD of the cage system for the loading condition given in Figure 2 Calculate the rod forces. tensile or tensile rod forces Specify the pressure. P1(kN)=20 P2(kN)=45 L3(m)=7
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.