General Background for Inductance of Transmission line 1- Introduction: 2- Derive one of the formulas used to find the flux linkages: 3- Calculation of Inductance of Transmission line (give an example):

General Background for Inductance of Transmission line 1- Introduction: 2- Derive one of the formulas used to find the flux linkages: 3- Calculation of Inductance of Transmission line (give an example):

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2MCQ: Overhead transmission-line conductors are bare with no insulating cover. (a) True (b) False

See similar textbooks

Related questions

Q: Consider an experimental 2000 kV three phase bundle-conductor line with 16-sub-conductors to each…

A: (c) Given Inductance in H per meter per phase is 0.744X10-6. Capacitance in Farads per meter per…

Q: Theoretically solve an unknown resistance for Transmission line conductor by using any two methods…

A: Wheatstone bridge This bridge is used to calculates the unknown resistance by balancing two legs of…

Q: 1. How do you measure three phase line currents by using two current transformers? Draw the…

A: The diagram for the three-phase system and the two current transformers are drawn below, Consider…

Q: A dc two line distributor AB 600 metre long is fed at 440 V from substation A and at 430 V from…

Q: a. What are the main components of overhead transmission lines (OHTL)? b. List commonly used…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: In a short paragraph, explain the need to use bundled phase conductors in HV, EHV, and UHV 3-phase…

A: Bundled conductors are made up of two or more stranded conductors that have been bundled together to…

Q: Calculate the inductance per phase per meter for a three- phase double-circuit line whose phase…

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The voltage…

Q: 6. Verify that the volume of conductor required in a transmission system is inversely proportional…

A: Power in Three-Phase circuit- Power depends on voltage, current and power-factor. Law's of…

Q: 3-phase, 126 MVA, 132 kV, 50 Hz, 355 mm² underground cable of outer radius 18 mm. Note: consider…

A: Given data, The supply frequency = 50Hz Area of the underground cable = 355mm2 The radius of the…

Q: QUESTION 1 Figure Q1 shows a single-line diagram of an 8-bus system. Line-1 and Line-2 have…

A: Part (c): Consider the base MVA is 50 MVA and base kVA is 22 kV. The base impedance is determined…

Q: write down the factors considered for selection of conductor for overhead LT distribution line.…

A: There are various factors need to be check before selecting conductor for over head transmission…

Q: In an over head transmission line the weight on the conductor due to wind is 2.35 kg. The total…

A: In overhead line weight on the conductor due to wind = 2.35kg Total weight = 3.45kg No ice loading…

Q: 4.5 A 60-Hz, 765-kV, three-phase overhead transmission line has four ACSR 900 kcmil 54/3 conductors…

Q: a) (i) Describe the main purpose of insulators in overhead transmission lines. (ii) Explain the…

A: transmission lines- Electrical transmission lines are very high Voltage, high power circuits usually…

Q: What is the maximum length in km for 3 phase transmission line having conductor of 0.875 square…

Q: a) Discus why the transmission systems are mostly overhead systems. b) Discuss why all overhead…

A: a) The transmission systems are mostly overhead systems: Electrical power transmission is the…

Q: 1) write down the factors considered for selection of conductor for overhead LT distribution line.

A: We have to write the factors considered for selection of conductor for overhead LT(Line…

Q: Problem #1 An overhead line has span of 260m. The tension in the line is 1200kg while the conductor…

A: Span, l= 260m Tension, T=1200kg Weight per unit length of the conductor, w=6501000=0.65kg/m

Q: Write about voltage drop and power loss for Radial d.c distribution system.

A: In the radial dc distribution system, various feeders are connected to the single substation such…

Q: a) Discus why the transmission systems are mostly overhead systems. b)Discuss why all overhead lines…

A: ACSR- Aluminium conductor steel-reinforced cable Bundled conductors- When a single phase conductor…

Q: 9- The main reason of using O.H.T.L instead of underground cables to transfer power is a-…

A: 9) The installation cost for overhead transmission line is less compared to underground cable since…

Q: In a power system having three conductors A, B and C of a 3-phase line carrying currents IA, IB and…

A: The three-phase line is represented by the phase A, B, and C, the current across the given conductor…

Q: Figure Q2 (a) shows the spacing of a double circuit 3-phase overhead line. The phase sequence is RYB…

A: 1) Significance of transposition of conductors When line is not transposed, There will be unequal…

Q: Q2. The Figure below shows the conductor configuration of a completely transposed three-phase…

A: Given data, Radius of conductor r =1 cm The bundle spacing d =5 cm Distance from between phase D=5…

Q: a). What is the reason for providing sag in an Overhead transmission line? b). List any two…

A: Whenever there is a need to send electricity to far off long distances, then the usage of overhead…

Q: What is the maximum length in km for 3 phase transmission line having conductor of 0.875 square…

Q: An Overhead transmission line has a span of 115 m. Ultimate strength is 3600 Kg and factor of safety…

Q: For the overhead line of configuration shown in Figure below operating at 60 Hz and a conductor…

A: Three-phase overhead line is shown below:

Q: Some electricians do not bother to calculate the minimum size of neutral service conductor. They…

A: 3-phase star connection balanced system does not require a neutral wire in the system. Basically, in…

Q: a List the factors affecting the sag of a transmission line. (write any three factors)

Q: How do you classify transmission lines? Subject Power Transmission and Distribution

A: Transmission line are classified as, (a) Short Transmission Line (b) Medium Transmission Line (c)…

Q: c) Referring to Figure 4, assume that there is a 300 MVA load at 0.8 lagging power factor at 132 kV…

A: Length of transmission line = 100 km it is medium transmission line. We use nominal pi network to…

Q: i) Discuss the essence of the mechanical design of a transmission line. ii) Discuss the advantages…

A: (i) Mechanical design of a transmission line (a) Height of tower The height of the tower depends on…

Q: Transmission line conductance is usually neglected in power system studies.

A: There are four parameters present in the transmission line: Inductance, capacitance, resistance and…

Q: (a) (i) Describe the main purpose of insulators in overhead transmission lines. (ii) Explain the…

Q: Example 4: Determine the efficiency and regulation of a 3-phase, 100 km, 50 Hz transmission line…

A: According to the question we have to find the value of efficiency and regulation with the help of…

Q: What happens when the sag in an overhead transmission line increases? How the sag varies when the…

A: The vertical distance between the points of consecutive supports and the lowest point of the…

Q: A three-phase transmission line is designed to deliver 190.5-MVA at 220- kV over a distance of 63…

Q: Figure 3 shows the one-line diagram of a three-bus power system with generation at bus X. The…

Q: Each line of a 3-phase system is suspended by a string of 3 similar insulators. If the voltage…

Q: Figure Q1 shows a single-line diagram of an 8-bus system. Line-1 and Line-2 have reactance 10 Q and…

A: lOAD -1 Values are-10 ohm,35 MVA,11KV lOAD -2 Values are-15 ohm,15 MVA,11KV For converting the…

Q: 5) Non minimum phase systems are also non causal. True False

A: Non-minimum Phase system: They are causal and stable systems whose inverse are causal but unstable.…

Q: Question 2 continued () Calculate in polar form the line-to-neutral voltages corresponding to the…

A: Given Parameters are: X=2, Y=8 Va0=1X0∠0oV=120∠0oV Va1=1Y0∠45oV=180∠45oV Va2=1Y0∠1X0oV=180∠120oV…

Q: 2 (a) Show that over the length of one transposition cycle of a power line, the total flux linkages…

A: Transmission lines- Transmission lines are basically a part of an electrical system, through which…

Q: Describe the effect of resistive load on sending and receiving end voltages, Power transferred and…

A: Effect of resistive load on sending and receiving end voltages, power transferred and Power factor.…

Q: In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across…

A: Given three phase overhead system , each line is suspended by a string of 3 insulators The voltage…

Q: In an over head transmission line the conductor weight with ice loading is 2.35 kg. The total weight…

A: As per bartleby guideline for more than one question asked only first is to answered please upload…

Q: single-phase power line comprises two conductors each with a radius 8.0 mm and spaced 1.2 m apart in…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

General Background for Inductance of Transmission line

1- Introduction:

2- Derive one of the formulas used to find the flux linkages:

3- Calculation of Inductance of Transmission line (give an example):

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the overhead line of configuration shown in Figure 4.33 operating at 60 Hz and a conductor temperature of 700C, determine the resistance per phase, inductive reactance in ohms/mile/phase, and the current-carrying capacity of the overhead line. Each conductor is ACSR Cardinal of Table A.4.
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.
Overhead transmission-line conductors are bare with no insulating cover. (a) True (b) False
For the case of double-circuit, bundle-conductor lines, the same method indicated in Problem 4.27 applies with r' replaced by the bundles GMR in the calculation of the overall GMR. Now consider a double-circuit configuration shown in Figure 4.36 that belongs to a 500-kV, three-phase line with bundle conductors of three subconductors at 21 in. spacing. The GMR of each subconductor is given to be 0.0485 ft. Determine the inductive reactance of the line in ohms per mile per phase. You may use XL=0.2794logGMDGMR/mi/phase
In a three-phase line, in order to avoid unequal phase inductances due to unbalanced flux linkages, what technique is used?
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Alumoweld is an aluminum-clad steel conductor. True False
Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
Shield wires located above the phase conductors protect the phase conductors against lightning. True False
Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Three ACSR Drake conductors are used for a three-phase overhead transmission line operating at 60 Hz. The conductor configuration is in the form of an isosceles triangle with sides of 20, 20, and 38 ft. (a) Find the capacitance-to-neutral and capacitive reactance-to-neutral for each 1-mile length of line. (b) For a line length of 175 mi and a normal operating voltage of 220 kV, determine the capacitive reactance-to-neutral for the entire line length as well as the charging current per mile and total three-phase reactive power supplied by the line capacitance.