GENERAL INSTRUCTIONS:SOLVE EACH OF THE FOLLOWING PROBLEMS AND SHOW YOUR SOLUTIONS FOREACH ITEM.1. A long-shunt compound generator supplies 50 kW at 230 V. the total field- and armature circuitresistances are 46 ohms and 0.03 ohms , respectively. The brush-contact drop is 2 V. Determine thepercent voltage regulation. Neglect the armature reaction.

% voltage regulation =100× (No load terminal voltage - full load terminal voltage)/(full load…

Answered: GENERAL INSTRUCTIONS: SOLVE EACH OF THE…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A thicker wire is used in the DC series field winding than DC shunt field winding in DC machines. * O because it carries the load current. O to prevent mechanical vibrations. O to provide strength. O to produce large flux. The speed of a DC motor can be changed by varying - armature resistance circuit O flux per pole O voltage source O all of above
A DC shunt generator delivers 45 A at a terminal voltage of 220 V. The armature and the shunt field resistances are 0.01 2 and 44N respectively. The stray losses are 375 W. What is percentage efficiency of the DC generator
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www Ish1 Rh1 a.350-360 V b.450-460 V c. 550-560V Rat www az G₂ Raz 5000 A Ish2
4. What for brushes are employed in DC generator? 5. What is the function of armature in a DC generator? 6. What is the function of commutator in a DC machine in generator action. 7 Whieh diffe u0ad in
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
For 6 polar D.C machine armature has 36 number of slots and the type of winding is a double layer simplex lap winding. a. How many coils are present? b. What is the coil span in terms of number of slots? c. If each coil has 4 turns, then what is the total number of armature conductors presents? d. How many parallel paths will be their in the armature? e. Altogether how many brushes will be their?
Q9 / What are the function of brushes , pole and commutator in DC machine
At rated voltage, a 125 kw, 300-V long shunt compound system provides power with a stray power loss of 3.69 kW. The winding resistors are as follows: armature=0.023, series field=0.04, shunt field=75. Under this condition, find the efficiency of the system.
Under load in DC machines, the armature current will cause: a. Compensating Windings O b. Increase in the main flux Oc Armature Reaction O d. Interpoles
State the Method of connection of different field coils. ( In DC Machines )
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning