a 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44 ohms. at rate load, the driving engine develops 62.26 hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses an Efficiency in DC Machine) (I need clean solution ma'am/sir, thank you so much)

a 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44 ohms. at rate load, the driving engine develops 62.26 hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses an Efficiency in DC Machine) (I need clean solution ma'am/sir, thank you so much)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

A 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44ohms. at rate load, the driving engine develops 62.26hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE) (I need a clean solution ma'am/sir. Thank you do much)
a dc shunt generator supplies a load of 10kW at 250V calculate the induced emf,if the armature resistance is o.5ohm and the shunt field resistance is 100ohm
3-phase, 50 Hz, 4-pole, 220 V, 10A ASM has an ASM 0.85 back power coefficient. stator copper losses are 500 W and rotor copper losses are 200 W. Friction and wind losses 100 W, core losses 300 W and stray load losses 50W. According to this; a. Air gap strength b. Mechanical strength produced c. Output power in horsepower D. Yield e. Slipping f. Working Speed g. Torque Produced h. Output Torque i. By specifying the asynchronous Motor power flow diagram from input to outputby drawing?
A 25kW, 250V DC shunt generator has armature and field resistances of 0.06 ohm and 100 ohm respectively. Determine the total armature power developed when working (i) as a generator delivering 25kW output and (ii) as a motor taking 25kW.
the armature series field and shunt field resistance of a 125 kw, 250V long shunt cumulative compound DC generator are 0.025ohms, 0.01ohms and 30 ohms, respectively. If the stray power stray loss at rated load is 25 kW, determine the power in the shunt field. Assume a astray load loss of 1% of the load power output (note: Input power generator is equal to the motor brake horsepower, Pin=Pl+Plosses) Choices A. 2034.5 W B.2082.5 W C. 2065.5 W D. 2053.5 W
Q1) A 4-pole, separately excited, wave wound DC machine with 0.12 armature resistance is rated for 230 V and 5 kW at a speed of 1200 rpm. If the same armature coils are reconnected to forms a lap winding, what is the power (in kW) at 1200 rpm of the reconnected machine if the field circuit is left unchanged? Also calculate the voltage regulation in both cases
A short shunt compound generator supplies a load of 10 kW at 200 V through a pair of feeder and series field resistance 0.10 ohm. Armature resistance, shunt field resistance and series field resistance are 0.01 ohm, 52.2 ohms and 0.10 ohm, respectively. If the core friction and windage losses amount to 631 watts, the BHP of the driving engine is nearest to
Q23) A shunt generator supplies a 20KW load at 200V through cables of resistance, R = 100mΩ. If the field winding resistance ,Rf=50Ω and the armature resistance, Ra=40mΩ, i) Estimate terminal voltage across the load. ii) Calculate the emf generated in the armature.
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *
N K © M =] v : @& docs.google.com/forms/d/¢ 2 Add file Q 1/ B) What is the work of Commutator . * &2, Add file Q 2) The following information is given for a 300-kW, 600-V, long-shunt compound generator : Shunt field resistance = 75 Q, armature resistance including brush resistance = 0.03 Q, commutating field winding resistance = 0.011Q, series field resistance = 0.012 Q, diverter resistance = 0.036 Q. When the machine is delivering full load, calculate the voltage and power generated by the armature * 2 Add file Q 3) A four pole aenerator havina - >
Q1) A 4-pole, separately excited, wave wound DC machine with 0.12 armature resistance is rated for 230 V and 5 kW at a speed of 1200 rpm. If the same armature coils are reconnected to forms a lap winding, what is the power (in kW) at 1200 rpm of the reconnected machine if the field circuit is left unchanged? Also voltage regulation in both cases
. A 480-V 200-kVA 0.8-power-factor-lagging 60-Hz two-pole Y-connected synchronous generator has asynchronous reactance of 0.25 Ω and an armature resistance of 0.03 Ω. At 60 Hz, its friction and windagelosses are 6 kW, and its core losses are 4 kW. The field circuit has a dc voltage of 200 V, and themaximum IF is 10 A. The resistance of the field circuit is adjustable over the range from 20 to 200 Ω.The OCC of this generator is shown in Figure P5-1.(a) How much field current is required to make VT equal to 480 V when the generator is running at noload?(b) What is the internal generated voltage of this machine at rated conditions?(c) How much field current is required to make VT equal to 480 V when the generator is running at ratedconditions?(d) How much power and torque must the generator’s prime mover be capable of supplying?