4. A generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 kW and 450kW. The station has a maximum demand of 22000 kW. The annual load factor of the station is 48%.Calculate (f) the number of units supplied annually (ii) the diversity factor and (iii) the demand factor.|(1) 925 x 10° kWh (i) 52-4% (ii) 1-9|5. A generating station has a maximum demand of 20 MW, a load factor of 60%, a plant capacity factor of48% and a plant use factor of 80% . Find :() the daily energy produced(ii) the reserve capacity of the plant

Since you have asked multiple questions, we will solve the first question for you. If you want any…

Answered: generating station supplies the…

generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 k . The station has a maximum demand of 22000 kW. The annual load factor of the stati

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Related questions

Q: A single-phase electrical load draws 1000KVA at 0.6 power factor lagging Find the real and reactive…

A: Given, A single phase load draws, S=100 kVA Power factor, cosϕ=0.6 lagging

Q: j0.20 ll 0.12 Load 124 kW Vs pf 0.9 lagging

Q: 2. Determine the average power P delivered by each of the three sources. 6 cos 377t A 155 cos 377t V…

Q: 1 12 kVA at power factor of @ the average calculate 0.86 agging from a sinusui dal source. and…

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: In this question, We need to determine the power supplied by the power company? If power factor…

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given: PL=300 kWcosϕ=0.6

Q: A certain load varies as follows for 269 days per annum: 436 kVA at a power factor of 0.819 lagging…

Q: Given a load in which V=10e^(jπ/3) and I=5e^(−j5π/6) calculate the power factor to a minimum of…

A: Power factor

Q: A certain load varies as follows for 269 days per annum: 436 kVA at a power factor of 0.819 lagging…

A: In the question, Find the average load per annum. Average load = total energy/ time

Q: 8 Ω -j2 N () 4/0 Α Ν

Q: -2. A. A lighting load of 2000 kW and a mo pplied by two alternators running in parallel E. lagging.…

Q: A generating station supplies the following loads: 15000 kW, 12000 kW, 8500 kW, 6000 kW and 450 W.…

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again.

Q: An equipment that draws 9.4 kW at 0.83 power factor lag. How much reactive power in kVAr is…

A: Reactive power = active power ×tan(power factor angle). Power factor angle = arc cos(power factor).…

Q: Question No.64 An industrial consumer has a load pattern of 2000 kW at 0.8 lagging for 12 hours and…

A: Given data: An industrial consumer has a load pattern of, Power demand, P1=2000 kW at 0.8 lagging…

Q: all V R sine sine Let the voltage source be 202135, the current source be 10245 and the impedance of…

A: In this question, We need to determine the value of resistance R if angle of current flow in this…

Q: A generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 kW and 45 kW.…

A: 5 loads are given 15000kW, 12000kW, 8500kW, 6000kW and 450kW. Maximum demand = 22000kW. Annual…

Q: Two alternators are working in parallel supply a lighting load of 3000 kW and a motor load…

Q: Determine the rms value of v(t)=5+10 cos(20πt).

Q: A generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 kW and 450 kW.…

A: Connected loads are Total loads are15000 kW, 12000 kW, 8500 kW, 6000 kW and 450 kW.

Q: Find the average power absorbed by the load with Z = 21 + j24 ohms

Q: IDm ALOO 100s2 Ikse

A: In the given circuit the three impedances 1000ohm, j100ohm, -j4ohm are in parallel. We will first…

Q: n alternator is supplying a load of 350 kW at a p.f of 0.7 lagging. If the power factor is raised to…

A: The solution is attached below for the given alternator problem.

Q: Volts 12 t (sec) Find the RMS value of the voltage waveform, Find the average power if 8 2 resistor,…

Q: certain load varies as follows for 269 days per annum: 436 kVA at a power factor of 0.819 lagging…

A: In the question, Find the average annual load factor Load factor = average load/ maximum load…

Q: Determine the complex power absorbed by the voltage source -j10 N j20 2 100/0° V rms 20 N 10 N

Q: What is the average power delivered by the power supply in the circuit shown below? 3 H 3Ω. + 5 cos…

A: We will find out current through source then power by using of average power formula.

Q: Calculate the average power þ Power Factor ww 8N N -jun 5010° deliverd by the 62 ww 11 fir source.

Q: A. The instantaneous If the rms values of voltage and current are 120 V and e power is, (a) 120-/2…

A: Instantaneous power Instantaneous power absorbed by an element is defined as the product of the…

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: This question belongs to circuit theory . It is based on the concept of power factor in the circuit…

Q: If there is 300 (phase 0) V rms voltage at the terminals of the loads given below, how many amps rms…

Q: A certain load varies as follows for 269 days per annum: 436 kVA at a power factor of 0.819 lagging…

A: In the question, Find the average load . Average load = total energy/ time

Q: 2. Determine the average power absorbed by cach resistor, the total average power absorbed and the…

A: Given figure as- I1=12∠45°4I1=3∠45°I2=12∠45°2-j1Ω=12∠45°2.236∠-26.56°I2=5.366∠71.56° A

Q: The average input to a manufacturing plant is 3.000 KVA at a power factor of 0.72 lagging. A…

Q: Let voltage across a load be v(t) = 20 + 40 cos(100t) volt and current through the load by i(t) =…

Q: If the rms values of voltage and current are 120 V and e A. The instantaneous power is, (a) 120/2…

A: Input =rms =120 V rms current =e-j20=1∠-300Imax=2∠-300 V=1202cosωt+00 Instantaneous power is given…

Q: Consider the following waveform. Volts 5 AA 12 t (sec) -5 Find the RMS value of the voltage…

A: RHS of common signals

Q: A certain load varies as follows for 269 days per annum: 436 kVA at a power factor of 0.819 lagging…

Q: An electric load operates at 100 V rms. The load absorbs 5 kW of power with lagging power factor of…

A: Given, Electrical load operating voltage, Vrms=100 V Load absorb power, P=5 kW Power factor,…

Q: Two alternators operating in parallel supply the following loads: A = 400W, unity pf; B=1000kW,…

Q: An electrical load operates at 240 V rms. The load absorbs an average power of 8 kW at a lagging…

Q: A power station has a maximum demand of 13590 kW. The annual load factor is 60% and plant capacity…

A: We have an power station and the data given about that power factor as below, Maximum Demand = 13590…

Q: A generation station has the following daily load cycle: 20-24 16-20 12-16 10-12 6-10 0-6 Time (h)…

A: we need to draw load duration curve.

Q: A 2 MW generation station has a daily average load of 500 kw with plant use factor of 0.8. The hours…

A: While setting up a power plant, taking care of generation economics is very important. If it is not…

Q: + 20 kW 16 kW 6/0° A rms 0.8 pf lagging 0.9 pf lagging

A: The solution is given below

Q: A 3 MW generation station has a load factor of 60 % and maximum load of 800 kw. The actual daily…

A: Load factor load factor is the ratio of average load to the maximum load in a given period of time.…

Q: Calculate the average power (P) absorbed by the load shown below when its impedance is 34+j46Ω and…

A: Given impedance is 34+j46 ohms and current Ix = 9.0 A rms here we have to find the average power.

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

100%

4. A generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 kW and 450
kW. The station has a maximum demand of 22000 kW. The annual load factor of the station is 48%.
Calculate (f) the number of units supplied annually (ii) the diversity factor and (iii) the demand factor.
|(1) 925 x 10° kWh (i) 52-4% (ii) 1-9|
5. A generating station has a maximum demand of 20 MW, a load factor of 60%, a plant capacity factor of
48% and a plant use factor of 80% . Find :
() the daily energy produced
(ii) the reserve capacity of the plant

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A generating station supplies the following loads : 15000 kW, 12000 kW, 8500kW, 6000 kW and 450 kW. The station has a maximum demand of 22000 kW. The annual loadfactor of the station is 48%.Calculate (i) the number of units supplied annually (ii) the diversity factor and (iii) the demandfactor.
2) The net inlet to a factory powered by a 2300 volt infinite busis measured as 765 A, for a lag 0.92 power factor. although mostloads is inductive, the input power factor has been improved by installing asynchronous capacitor operating at its nominal value of 1000 KVA. Determine the factor oforiginal factory power.
A system is working at its maximum kVA capacity with a lagging power factor 0·7. An anticipated increase of load can be met by one of the following two methods: By raising the p.f. of the system to 0·866 by installing phase advancing equipment. By installing extra generating plant. If the total cost of generating plant is Rs 100 per kVA, estimate the limiting cost per kVA of phase advancing equipment to make its use more economical than the additional generating plant. Interest and depreciation charges may be assumed 10% in each case.
Q3: A power supply is having the following loads: Type of load Maximum demand (kW) | Diversity of group | Demand factor Domestic 15000 125 0.8 Commercial 25000 1.2 1 Industrial 50000 13 0.5 If the overall system diversity factor is 1.5, determine: 1. The maximum demand. 2. Connected load of each type.
A generating station supplied the following loads: 150 MW, 120 MW, 85 MW, 60 MW, and 5 MW. The station has a maximum demand of 220 MW. The annual load factor of the station is 48%. Calculate : 1) the number of units supplied annually 2) diversity factor 3) demand factor
A generating station supplies the following loads: 15000 kW, 12000 kW, 8500 kW, 6000 kW and 450 kW. The station has a maximum demand of 22000 kw. The annual load factor of the station is 48%. Calculate (i) the number of units supplied annually (ii) the diversity factor and (ii) the demand factor.
A three-phase system includes a 346.4 V line-to-line supplying a three-phase motor rated 15KVA 0.8pf lag plus additional balanced constant impedance loads. The single-phase representation of the system is shown below. Assume that sources and loads are Y-connected. 1. What is the RMS value of the line current, I in A? 2. If this set of loads will be supplied through a service transformer. What should the minimum size of the transformer in kVA? 3. What should be the size of three-phase capacitor(that will be added to the load mix) to improve power factor to almost 0.95 lag?
A 3000 kW diesel station supplies the following loads to various consumers : Industrial consumer = 1500 kW Commercial establishment = 700 kW Domestic power = 120 kW Domestic light = 480 kW If the maximum demand on the station is 2600 kW and the number of kWh generated per year is 40 ×105. Determine: (i) Diversity factor . (ii) Annual load factor. (iii) Reserve capacity of the station.
The yearly load duration curve of a certain power station can be approximated as a straight line ; the maximum and minimum loads being 80 MW and 40 MW respectively. To meet this load, three turbine generator units, two rated at 20 MW each and one at 10 MW are installed. Determine (i) installed capacity (ii) plant factor (iii) kWh output per year (iv) load factor.
. A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If the station has a load factor of 35%, solve the demand factor of the station. Answer: 0.4179 or 41.79% Subject: Distribution System and Substation Design
1. Voltage between 1 kV and 50 kV is defined as: A.Very High Voltage B.Medium Voltage C.Low Voltage D.High Voltage A factory consumes 400, 000 kVAh in a year witth the yearly average power factor 0.75. Calculate the average demand and percentage of annual load factor if the maximum demand is 120kW. A.Average demand = 44.25kW, Load factor = 29% B.Average demand = 44.25kW, Load factor = 39% C.Average demand = 34.25kW, Load factor = 29% D.Average demand = 34.25kW, Load factor = 39% The example of low voltage system is: A.Three-phase, 4-wire, 415 V, up to 45 kVA maximum demand B.Three-phase, 3-wire, 66 kV, 132 kV and 275 kV for exceptionally large load of 25 MVA maximum demand C.Three-phase, 3-wire, 11 kV for load of 1000 kVA maximum demand and above D.Three-phase, 3-wire, 22 kV or 33 kV for load of 5000 kVA maximum demand and above A load rises from zero to 20 kW instantaneosly and stays constant for 2 minutes, then rises about 40…
A 550-V feeder line supplies an industrial plant consisting of a motor drawing 60 kW at 0.75 pf (inductive), a capacitor with a rating of 20 kVAR, and lighting drawing 10 kW. (a) Calculate the total reactive power and apparent power absorbed by the plant. (b) Determine the overall pf. (c) Find the current in the feeder line.