Get the sum of the two signals. V1 = a sin (120nt + b) V2 = c cos (120nt + d) Pick the values of [ a, b, c, d ] from this file: CIRCUITS2-PRELIM-Addition-of-Waves.pdf Answer this way: 2000888888 V1 = 12 sin (120t – 10°) V2 = -10 cos (120tt + 50°) V3 = 21.2567 sin (120nt – 23.6046°)

Get the sum of the two signals. V1 = a sin (120nt + b) V2 = c cos (120nt + d) Pick the values of [ a, b, c, d ] from this file: CIRCUITS2-PRELIM-Addition-of-Waves.pdf Answer this way: 2000888888 V1 = 12 sin (120t – 10°) V2 = -10 cos (120tt + 50°) V3 = 21.2567 sin (120nt – 23.6046°)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

https://www.bartleby.com/questions-and-answers/question-the-electric-field-component-of-a-5.6-ghz-plane-wave-is-given-by-ef1-a0.4915-j0.8550e1573.0/518344cd-770a-49a0-9191-651965a29cd8
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 kohm, Rohm = 0.5 kQ, R1 = 75 kohm, R2 = 15 kohm, RC = 2.2 kohm, RE = 1 kohm and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
When Ri=0 in the circuit given above, the frequency a is 1.5 kHz in the amplitude spectrum drawn. The capacitance of the capacitor for the same circuit is 1.8 microF. What should be the value of the resistor R so that the quality factor remains unchanged at 3.3 when the resistor Ri is 1.8 ohms?answer choices are in the picture
In the amplitude spectrum drawn when Ri=0 in the circuit given aboveThe frequency a is 2.4 kHz. The capacitance of the capacitor for the same circuit is 0.7 microF.The quality factor remains unchanged at 3.2 when the resistance Ri is 1.9 ohms.What should the value of resistor R be for it to stay put?
Connect the circuit shown in Fig. with R=1 kΩ and C=0.1 μF. Set the function generator to square wave with f=100Hz and Vp-p=10 volt.Sketch Vc, Vr and Vs to the same time scale.
Which of the the following statements concerning the phase angle compensator is true? A. It is a dc voltage source B. It is an ac voltage source with a controllable amplitude and uncontrollable phase angle C. It is an ac voltage source with a controllable amplitude and uncontrollable amplitude D.t is an ac voltage source with both a controllable amplitude and phase angle
388 / 5000 Çeviri sonuçları In the circuit in the figure, Rs = 3.8 kΩ, R1 = 82 kΩ, R2 = 22 kΩ, RC = 5.6 kΩ, RE = 1.5 kΩ and RL = 3.3 kΩ and β = 150.Since the capacitances are C1 = 0.5 μF and C2 = 0.53 μF, what is the low cutoff frequency of the given circuit? NOTE-1: In the middle band frequency, β = 150 will be taken and the frequency dependence of β will not be taken into account. NOTE-2: The output impedance of the transistor r0 will be neglected in the calculations.
An inductor, a capacitor, and a resistor are all connected inseries across an ac source. If the resistance, inductance, and capacitanceare all doubled, by what factor does each of the following quantitieschange? Indicate whether they increase or decrease: the resonance angular frequency
ı just need fınal aswer In the circuit in the figure, Vcc = 18 V, Rs1 = 0.9 kΩ, Rs2 = 0.5 kΩ, R1 = 75 kΩ, R2 = 15 kΩ, RC = 2.2 kΩ, RE = 1 kΩ and β =120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = Cπ = 58 pF and Cce = 11 pF. Accordingly, considering the frequency response of the circuit, what would be the high cutoff frequency (fH)? NOTE-1: The output impedance of the transistor is r0 = 20 kΩ and will be considered in the calculations. NOTE-2: The high frequency dependence of hfe, that is β, will be taken into account. a. 189,95 kHz b. 617,33 kHz c. 569,84 kHz d. 474,87 kHz e. 332,41 kHz f. 47,49 kHz g. 142,46 kHz h. 712,30 kHz
a) What is the dominant mode if a<b in a rectangular waveguide? This mod's cutWhat is wavelength?b) If the waveguide is quadratic (a=b) the cutoff frequencies of the TM11, TE20 and TE02 modeswhat?c) Explain what SWR is.d) Connect a parallel plate capacitor to an ac source that changes değişen Vc = V0(sinwt)Calculate the displacement current (id) when you connect it. Comment the result.
A 10-MHz sinusoidal carrier wave of amplitude 10 mV is modulated by a 5 kHz sinusoidal audio signal wave of amplitude 6 mV. :1- Draw the wave form of the resualtant modulated signal.2- Draw the frequency spectrum of the resultant modulated wave and their amplitudes
In the circuit given above, the frequency a is 1.7 kHz in the amplitude spectrum drawn when Ri=0. The capacitance of the capacitor for the same circuit is 0.5 microF.What should be the value of the resistor R so that the quality factor remains unchanged at 2.0 when the resistor Ri is 1.9 ohms?