1. Construct the circuit shown above. 2. Measure the values of , L, hand lgusing Digital Multimeter (DMM). 3. Measure V14 voltage from point 1 to point 4 V2-4 voltage from point 2 to point 4 V34 voltage from point 3 to point 4 V1-2 voltage from point 1 to point 2 V23 voltage from point 2 to point 3 1, loon 2 2202 3 1s 15V lov 60on 15V

1. Construct the circuit shown above. 2. Measure the values of , L, hand lgusing Digital Multimeter (DMM). 3. Measure V14 voltage from point 1 to point 4 V2-4 voltage from point 2 to point 4 V34 voltage from point 3 to point 4 V1-2 voltage from point 1 to point 2 V23 voltage from point 2 to point 3 1, loon 2 2202 3 1s 15V lov 60on 15V

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 24RQ

See similar textbooks

Similar questions

ANSWER ALL, I WILL UPVOTE IF CORRECT 16. the sum of the firing delay angle and the conduction angle is 360. true or false 17. it is a breakover type of device that turns on when the voltage across its terminals exceed a certain value. a. Thyristor b. BJT c. Transistor d. MOSFET 18. What is the maximum firing delay angle that can be achieved with a resistive gate control circuit? a. 180, b. variable, c. 360, d.90 19. It is the minimum amount of gate current that will make the SCR conduct current. given that the gate-cathode voltage is 0.7V. a. saturation current, b. gate conduction current, c. gate tunrn on current, d. holding current 20. When the anode is made positive with respect to the cathode of the SCR but there is no gate current, The SCR is operating in its a. off region, b. forward blocking region, c. forward breakover region, d. reverse blocking region
ANSWER ALL, I WILL UPVOTE IF CORRECT 16. the sum of the firing delay angle and the conducion angle is 260. true or false 17. it is a breakover type of device that turns on when the voltage across its terminals exceed a certain value. a. thyristor, b. BJT, c.Transistor, d. MOSFET 18. What is the maximum firing delay angle that can be achieved with a resistive gate control circuit? a. 180, b. variable, c.360, d.90 19. it is the minimum amount of gate current that will make the SCR conduct current given that the gate-cathode voltage is 0.7V a. saturation current, b. gate conduction current, c. gate turn-on current, d. holding current 20. When the anode is made positive with respect to the cathode of the SCR but there is no gate current. The SCR is operation in its? a. off region, b.forward blocking region, c. forward breakover region, d. reverse blocking region
Draw the V-I characteristics of SCR,MOSFET,IGBT,DIAC and TRIAC
draw the curcuit diagram for 4 channel 4 bit multiplexer implemented using 4 channel 1 bit multiplexer. make sure that i need full circuit to save the final multiplexer in the library.
Define “Voltage Instability”. Give an details voltage stability analysis for an SMIB system.
make a protection circuit with a UMW SI2301A pchannel mosfet
Are the following statements correct or wrong? Justify your answer. (a) GTO requires very low current applied to its gate to be turn off. (b) IGBT is a voltage driven device. (c) BJT is more efficient than IGBT in high power applications. (d) Thyristors are used only for low voltage, low current applications. (e) MOSFETs are used for high frequency applications.
compare the analog voltage divider method for handling switches versus the multiplexer method. In particular, consider their ability to scale to a large number of switches, relative complexity in hardware and programming, and the number of I/O lines needed on the microcontroller to support each method.
17. For the set of input waveforms in Figure 3–83, determine the output for the gate shown anddraw the timing diagram.? 1. Repeat Problem 17 for an exclusive-OR gate.?
3. A programmable unijunction transistor (PUT) is programmed by choosing the a. gate resistors b. RC time constant c. Cathode resistor d. power supply voltage 4. What is the most popular type of Thyristor? a. DIAC b. TRIAC c. UJT d. SCR 5. For an SCR to turn OFF, the gate has a. To be more negative than the anode b. To be more positive than the cathode c. To be more positive than the anode d. Nothing to do with SCR to turn OFF
During turn-on and turn-off of a power transistor, thecurrent-time and voltage-time relationships are asshown in the adjacent figure. Observe the waveformsand calculate,40) the OFF-state power dissipation (static);41) the switch ON-state power dissipation(static);42) the average switching loss for the OFFtransition (dynamic);43) the average switching loss for the ONtransition (dynamic);Assume a switching frequency of 2kHz with 397V as specified in Appendix A.
Sketch the following particulars for the device which is having low on state loss and used in very small switching frequency operation. (i) Symbol with terminals name (ii) Cross sectional view (iii) Static characteristic