Give detailed information about Jury’s stability test.What are the conditions for Jury’s stability test?

Q: The is known as the final control element . -

A: The final element in the control system is that element which is responsible or the output of the…

Q: Does varying the motor field current Ip vary the motor speed n? O Yes O No Does varying the motor…

A: In this question we need to verify the given statement is true or false.

Q: What is the battery balancing? Explain the balancing types.

A: The explanation is as follows.

Q: Question 6: 1- List the pins on Arduino that can do analog write. 2- In a PWM, given that the duty…

A: On most Arduino boards analogwrite() function works on pins 3, 5, 6, 9, 10, and 11.

Q: Find the number of turns

A:

Q: how to test the cable with testers and instruments

A: An electrical cable is an assembly of one or more wires running side by side or bundled, which is…

Q: According to what is the calculation of engine power in industry according to the load.

A: Different energy sources are required in day to day life. These energy sources can be renewable or…

Q: Two shunt generators and a battery are all connected to common bus-bars. The open circuit voltage of…

A: This problem is of electrical machine

Q: In short tell the difference in the stepper and servo motor.

A: The difference in the Stepper and Servo motor: The difference in the Stepper and Servo motor: The…

Q: calculate the iron loss of motor at rated voltage. for what depend mainly the iron losses

A: IRON LOSSES (CORE LOSSES): The following two types of iron losses take place in the core due to the…

Q: In static characteristics, is specified at only one particular point of scale.

A: Static characteristics: It is used to measure the quantities that are slowly varying with time or…

Q: When the rotor angle is increasing with respect to time, then the stability of the power system will…

A:

Q: Write a note on split rings in machines with the help of diagram.

A: The description and relevant diagram of split ring is shown below.

Q: 3. Write any four differences between NC and CNC machines.

A: Ans. Given below

Q: what is vehicle servicing

A: A motor vehicle service or tune-up is a series of maintenance procedures carried out at a set time…

Q: (B)-Draw a neat diagram to show potential divider arrangement of rheostatic control speed for d.c.…

A: Potential divider arrangement of rheostatic control speed for D.C. shunt motors: Rf Field…

Q: For shunt generator which kind of apparatus is used for adjusting the voltage

A: For shunt generator, the potentiometer is used for adjusting the voltage. It controls the field of…

Q: What are the instruments used in test for fans and blowers?

A: It is asked which the instruments are used in test for fans and blowers.

Q: cus for the following control system s.

A: Root locus is the locus of roots of characteristics equation when gain parameter is varied from zero…

Q: Discussion and conclusion based on the pic

A:

Q: It is the most commonly used stepper motor driver which is directly connected to the PC.

A: The most commonly used stepper motor driver which is connected to the pc is " ULN2003".

Q: Explain how does the current will be reduced during the starting of the motor.

A: According to question we have to explain, how does the current will be reduced during the starting…

Q: Explain the construction and operation of CRO with diagram.

A:

Q: What is the area of ​​the shaded part

A:

Q: For P pole machine relation between electrical degrees and mechanical degrees is *

A: For a p pole machine θmech is  given by, θmech=P2 θelc

Q: A distributor arranged to form a closed loop

A: A distributor arranged to form a closed loop and fed at one or more points is ring distributor ,…

Q: Duestion of Write down the construction alternatOx with the an of diagram of operation. and write…

A: The alternator is also called the synchronous generator is an electrical machine that is used to…

Q: ii. The generation voltage is in simulator is ...Volts.

A: In the simulator, the generation voltage and current source are showing on the display of the LED of…

Q: Consider a group of students that are sifting through a crate with broken or malfunctioning cables,…

A: Cable faults can be found by looking for Ethernet symbol errors on switch and router interfaces.…

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: Fill in the blank _______________ is possible because of the residual magnetism in the stator pole…

A: When current is reduced to zero then there will be magnetic power still left in the core of the coil…

Q: How Get = S+2 Rind the first order in control system and draw

A: Important Notes about first order system  First order system can be described by first order…

Q: Draw the block diagram and clearly explain the operation of diesel power station.

A: The block diagram is shown below:

Q: Symbol of LED

A:

Q: Answer by true or false True False - As the load is increased gradually, the load current increases…

A: As the load is increased gradually, the load current increases but the terminal voltage decreases…

Q: What type of motor changes speed by changing the number of stator poles

A: Given  What type of motor changes speed by changing the number of stator poles

Q: "Order" of the following control system is

A:

Q: CCA stands for common ampere Select one : False or True

A: CCA stands for 'Common Collector Amplifier' not common ampere.

Q: b) With sketch of diagram, show the number of resistor and switched would be required to implement…

A:

Q: Mark all the parts of gas pressure cable in pictures

A: Gas pressure cable : it an coaxial or simple cable which filled with inert gas like nitrogen at…

Q: stability

A:

Q: xplain with neat diagram two type of Flat belt drives with applicatio

A: Open belt drive. The open belt drive,  is used with shafts arranged parallel and rotating in the…

Q: Questions:- 1. How voltage is built up in D.C. shunt generator?

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: Explain the concept of “grounding”

A: The neutral points of the transformer and generator are earthed as part of the system earthing. When…

Q: Explain the construction and operation of instrument whose deflecting torque is proportional to the…

A:

Q: Differences between VFD and Soft Starter,include their applications and when are they used

A: To differentiate between VFD and Soft starter