Give two (2) examples of light vehicle automatic transmission and driveline system faults chosen from electronically controlled automatic transmissions continuously variable transmissions (CVTs) constant velocity joints Hookes-type joints rear wheel drive shafts rear wheel drive final drives front wheel drive final drives for each of the following: (5 - 10 words each) Intermittent faults Multi-system faults Introduced as a result of a system repair Indirect, caused by the influence of external systems

Give two (2) examples of light vehicle automatic transmission and driveline system faults chosen from electronically controlled automatic transmissions continuously variable transmissions (CVTs) constant velocity joints Hookes-type joints rear wheel drive shafts rear wheel drive final drives front wheel drive final drives for each of the following: (5 - 10 words each) Intermittent faults Multi-system faults Introduced as a result of a system repair Indirect, caused by the influence of external systems

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter42: Electronic Automatic Transmissions

Section: Chapter Questions

Problem 7RQ: Most late-model transmission control systems have adaptive learning. What does this mean?

See similar textbooks

Similar questions

Audi’s design of their R8 model is designed in order to have the engine in the rear of the car with the following schematic of their mechanical power transmission. The engine is connected to the gearbox, where gear change occurs and then a driveshaft is used to transfer an equal ratio of power balancing the rear and front wheel power output thus referring to it as an all-wheel drive. The vehicle has been modified by a customer thus resulted to no power transfer to the front wheels although the rear wheels still have the same power output. 1) DEFINE and JUSTIFY the possible reasons of why the front drive isn’t functioning? 2) What are the solutions to this fault?
what factors determine the design of the power transmission mechanisms in a rear wheel drive van (Diesel) and how do you calculate power and torque at the driveshaft, assuming the following: its 5 speed transmission, Gear system efficiency is 88% Gear ratios: 1 st: 4.17:1 2 nd 2.34:1 3 rd 1.52:1 4 th 1.14:1 and power and torque to be calculated at the point where engine is generating its maximum power
Give one example for each of lightvehicle steering and suspensionsystemsa) hydraulic power assisted steeringb) adaptive suspensionfor each of the following: (5 -10words each)a. b. c.Intermittent faultsMulti-system faultsIntroduced as a result of asystem repaird.Indirect, caused by theinfluence of external systemsIn your answer, briefly explain theprocess that would be followed todiagnose the fault
pleassssse solve question 1, statics
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
briefly define the following: 1. airborne transmission 2. common vehicle transmission 3. contact transmission
Words: Axles, Differential, Gear, Housing, Propelled, Ring, Side, Transaxle, Transfers, Transmission, Vehicles,WeightFront-wheel drive (FWD) vehicles are ________________ by the front wheels. For this reason, they must use a drive designdifferent from that of a RWD vehicle. The ________________ is the special power transfer unit commonly used on FWDvehicles. A transaxle combines the transmission gearing, ________________, and drive axle connections into a single case________________ located in front of the vehicle. This design offers many advantages. One major advantage is the goodtraction on slippery roads due to the ________________ of the drivetrain components being directly over the driving________________ of the vehicle. It is also more compact and lighter than the ________________ of a RWD vehicle.Transverse engine and transaxle configurations also allow for lower hood lines, thereby improving the ________________aerodynamic.The final drive ________________ gear is driven by the…
Explain the role of shift rails and shift forks in theoperation of a transmission or transaxle.
Give two (2) examples of light vehicle diesel engines faults for each of the following categories (20-30 words each): Intermittent faults Multi-system faults Faults introduced as a result of a system repair Indirect faults caused by the influence of external systems
Most late-model transmission control systems have adaptive learning. What does this mean?
Answer the following questions on vehicle safety system diagnostic trouble codes (DTCs). Relating to a 2016 ND Mazda MX5 What is U3003:16 the diagnostic trouble code (DTC) for? What system component sets the U3003:16 DTC? What system condition is required to set the U3003:16 DTC? What are the conditions required to run a U3003:16 DTC. Briefly explain the fault symptom(s) associated with the U3003:16 DTC.
Words: Accelerating, Float, Gear, Noise, Tooth, VehicleCrown wheel and pinion noise originates from poor ________________ contact and may be noticed on drive, overdrive or________________. It can be more pronounced on one of these than on the others.Drive noise is most pronounced when ________________, as the gear teeth are under load. The bearings are also under loadso that any lack of preload will allow the ________________ teeth to change their area of contact.Noise on overdrive occurs as the ________________ decelerates from medium speeds, while float ________________occurs under light cruising conditions.