Given: A pipe connecting two reservoirs as shown in Fig. 1. Absolute roughness of both pipe sections is 0.5 mm. Calculate: a) Equivalent pipe loss coifficient b) Equivalent pipe length which can replace the secondary losses c) Discharge in the two pipes (ignore secondary losses) d) Equivalent pipe diameter required to replace the two pipes in series (Leq = 2500m) e) Sketch EGL ( solid line) and HGL (dash line) H= 50 m L= 1000 m - 2000 m- Water 20°C D= 200 mm Valve D=300 mm Figure 1 (Half closed)

Given: A pipe connecting two reservoirs as shown in Fig. 1. Absolute roughness of both pipe sections is 0.5 mm. Calculate: a) Equivalent pipe loss coifficient b) Equivalent pipe length which can replace the secondary losses c) Discharge in the two pipes (ignore secondary losses) d) Equivalent pipe diameter required to replace the two pipes in series (Leq = 2500m) e) Sketch EGL ( solid line) and HGL (dash line) H= 50 m L= 1000 m - 2000 m- Water 20°C D= 200 mm Valve D=300 mm Figure 1 (Half closed)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer ( Show all steps ) Question : A good curve-fit to the head vs. flow for the 32-inch pump in the image shown below is: H(inft)≈500−(2.9E−7)Q2, Q in gal/min Assume the same rotation rate, 1170 r/min, and estimate the flow rate this pump will provide to deliver water from a reservoir, through 900 ft of 12-inch pipe, to a point 150 ft above the reservoir surface. Assume a friction factor f = 0.019. What is the pump efficiency at this operating point??? HINT : 150 ft above the reservoir surface.
Identify how the hydro resource of a river can be described.
Water flows through a horizontal pipe of cross sectional of 20 cm2. Atone section, the cross sectional area is 4 cm2. the pressure difference is29.4 psi. How many cubic meters of water will flow out of the pipe in 1min? (can you show the diagram or illustration if possible. thank you!) Choices: a. 0.008 b. 1.208 c. 0.493 d. 0.0185
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
Hello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1. ) Question : A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting frictional losses, calculate the volume flow rate (m3/min) if the discharge is raised 60 meters above.Answer: 1.82
5. Write down the Benoulli equation and explain the meaning of each terins 6. Water is flowing through a hole at the bottom of large tank filled with water. Tank is open to atmosphere. The level of water in the tank is 20 m Calculate velocity of flow. Assume steady flow and neglect viscous effects. 20 m 2 Tig.1 F. 1.0 P-100 kPa Handwriting not allow please
Please help me with this problem clearly. List two sources of error in the water-filled tube and pressure gauge method of measuring head for a hydro system and how to avoid them. Using this method, a series of measurements up a hill to the source of the stream produces the following heights: 1.5m, 0.7m, 1.0m, 1.9m, 1.6m, 0.3m, and 0.8m. What is the total head for this site? If the flow rate was 0.5 m3s-1, calculate the power available in this stream?
After graduation, you work for a pump manufacturing company. One of your company’s best-selling products is a water pump, which we shall call pump A. Its impeller diameter is DA = 6.0 cm, and its performance data when operating at n. A = 1725 rpm (?A = 180.6 rad/s) are shown in Table.The marketing research department is recommending that the company design a new product, namely, a larger pump (which we shall call pump B) that will be used to pump liquid refrigerant R-134a at room temperature. The pump is to be designed such that its best efficiency point occurs as close as possible to a volume flow rate of V. B = 2400 cm3 /s and at a net head of HB = 450 cm (of R-134a). The chief engineer (your boss) tells you to perform some preliminary analyses using pump scaling laws to determine if a geometrically scaled-up pump could be designed and built to meet the given requirements. (a) Plot the performance curves of pump A in both dimensional and dimensionless form, and identify the best…
HYDRAULICS Benzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter per second.
In a chemistry plant, through a horizontal smooth pipeline with a diameter of 0,3 m, a fluid with density and viscosity of 769 kg/m3 and 0,0007 Pa-s, respectively is flowing with a flow rate of 0,009 m3/s. Disregarding the pipe entrance effects and treating flow being steady, uniform and incompressible; a) Find the magnitude of mean velocity (in m/s). (Please use only 3 decimal digits.) b) Find Reynolds number. (Please do not use any decimal digit.) c) Find the magnitude of friction factor. (Please use 4 decimal digits.)
Pls answer asap. What is the velocity of flow for circular pipe flowing full having a diameter of 250 mm if the friction loss is 25 m in a length of 75 m if the Chezy coeffcient is 10 m^1/2 /s . Write your answer to the nearest two decimal places
What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the design velocity if the system is 3 m/s?