I need the answer as soon as possible lengthof RoPeGiven: (M & K ??Ed ??) The systen shown is released from rest. The weight of block A is WA = 30 lbf andthe weight of block B i WB = 5 lbfFBD OF A?18 3T!20SBB.SHOWBDTRECIIONNOT -a"Find: Assuming1. the accelerations of each mass at the instant of release,2. the tension in the rope at the instant of relcase &3. the velocity of each mass after 5 seconds has passed

Answered: Image /qna-images/answer/efbabdbf-8bd6-4f66-99af-3b92c0c86f91.jpg

Answered: Given: (M & K ??Ed ??) The systen shown…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A motorcycle starts from rest at t = 0 and travels along a circular track with a 350-m radius. The tangential component of the total force on the motorcycle from t = 0 to t = 30 s is ∑ ?? = (200 − 6?) ?. The combined mass of the motorcycle and rider is 200 kg. (a) What is the magnitude of the velocity at t = 30 s? (b) What is the average of the tangential and normal component of the total force from t = 0 to t = 30 s?
A small 0.18 kg metal ball is tied to a very light (essentially massless) string that is 0.60 m long. The string is attached to the ceiling so as to form a pendulum. The pendulum is set into motion by releasing it from rest at an angle of 50 degrees with the vertical. I solved that the speed of the ball when it reaches the bottom of the arc is 2.0 m/s and the tension of the string is 3.0 N What is the centripetal acceleration of the ball at this point?
By using a forked rod, a smooth cylinder C having a mass of 0.5 kg is forced to move along the vertical slotted path (r = 0.4 θ) m, where θ is in radians. If the angular position of the arm is θ = (0.3 t3 ) rad, where t is in seconds. The cylinder is in contact with only one edge of the rod and slot at any instant. Find "the force of the rod on the cylinder at the instant t=2s" Find "the normal force of the slot at the instant t=2s" Find the "radius of curvature at t=2s" Find the "ψ angle at t=2s"
simple pendulum is made of a 50 cm-string and a bob of mass m. At t= 0, the pendulum is at its equilibrium position and is given an initial velocity v = 0.2 m/s. The maximum angular speed, O'max, is:
A lightweight drone (1.00 kg) is launched at 800 m high and moves upward at a constant velocity (whileignoring the effects of gravity only on the drone). The balloon, when measured at a horizontal distance fromyou, is about 1600 m away from you. At the moment when the drone moves, you shoot a bullet (weight =180g) with an initial velocity of 1009 m/s at a fixed angle α, where sin α=3/5 and cos α= 4/5. (g = 9.8 m/s2) d. Provided that the collision is inelastic, calculate the speed after the collision.e. Calculate the height the two objects taken from the impact up to the maximum height before it startsfalling to the ground.
a=22mist 16w/ Figure Q) “The mass of ahuckey puck 0.80Kg slides on horizontal, frictionless surface of an ice rink. If two hockey sticks srike the puck simulaneously, exerting the acceleration of the puck shown n figure 2. Determine both the magnitude and the direction of the puck’s forces?
The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
Dynamics Question If the normal acceleration of the rods is just w^2 * 1.5m, is the normal acceleration of the 50-kg bar just w^2* 2m?
A mass of 20 kg is suspended from a spring of stiffness 10000 N/m andthe vertical motion of mass is subjected to coulomb friction of magnitude50 N. if the spring is initially displaced 5 cm downwards from its staticequilibrium position. Determine the number of cycles before the bodycomes to rest.
A weight stretches a spring 6 in. It is set in motion at a point 2 in. below its equilibrium position with a downward velocity of 2 in./sec. a. When does the weight return to its starting position? b. When does it reach its highest point? c. Show that the maximum velocity is 2sqrt(2g + 1) in./sec.
9. A spring has a stiffness of 100N/m. A mass of 3 kg was attached to the spring. The mass was pushed 10cm upward from the equilibrium position and was released from rest. After 5 seconds from release, determine the acceleration of the mass in m/s^2? 10.What Law governs the statement, "For every object applied with a load, the displacement or size of deformation is directly proportional to the magnitude of the applied load"?
A 2kg body, attached in a 25cm string, is under a uniform circular motion with a velocity of 2m/s. Determine the centripetal force in Newtons

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS