Given that the delivered power to a resistor is equal to P when the current flowing in the resistor is l. If the curren increased to 7.9 lo the delivered power to the resistor will be: Select one: OA. 124.8 P OB. 15.8 P OC. 62.4 P OD.0.1 P DE79P

Given that the delivered power to a resistor is equal to P when the current flowing in the resistor is l. If the curren increased to 7.9 lo the delivered power to the resistor will be: Select one: OA. 124.8 P OB. 15.8 P OC. 62.4 P OD.0.1 P DE79P

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter20: Electric Current, Resistance, And Ohm's Law

Section: Chapter Questions

Problem 14CQ: The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance...

See similar textbooks

Similar questions

Resistors are commonly rated at 18W,14W,12W ,1 W and 2 W for use in electrical circuits. If a current of1 = 2.00 A is accidentally passed through a R=1.00 resistor rated at 1 W, what would be the most probable outcome? Is there anything that can be done to prevent such an accident?
Consider a power plant is located 60 km away from a residential area uses Q-gauge (A=42.40mm2) wire ofcopper to transmit power at a current of I = 100.00 A.How much more power is dissipated in the copper wires than it would be in superconducting wires?
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
Consider a resistor made from a hollow cylinder of carbon as shown below. The inner radius of the cylinder is Ri= 0.20 mm and the outer radius is R0 = 0.30 mm. The length of the resistor is L = 0.90 mm. The resistivity of the carbon is =3.5105 m. (a) Prove that theresistance perpendicular from the axis is R=2L1n(R0Ri) . (b) What is the resistance?
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
Consider a series RC circuit as in Figure P28.38 for which R = 1.00 M, C = 5.00 F, and = 30.0 V. Find (a) the time constant of the circuit and (b) the maximum charge on the capacitor after the switch is thrown closed. (c) Find the current in the resistor 10.0 s after the switch is closed.
If you were to design an electric heater using Nichrome wire as the heating element, what parameters of the wire could you vary to meet a specific power output such as 1 000 W?
Explain why R=R0(1 + a?T) for the temperature variation of the resistance R of an object is not as accurate as P=P0(1 + a?T) which gives the temperature variation of resistivity P.
A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg • °C, assuming no heat escapes?
The potential difference across the filament of a light-bulb is maintained at a constant value while equilibrium temperature is being reached. The steady-state current in the bulb is only one-tenth of the current drawn by the bulb when it is first turned on. If the temperature coefficient of resistivity for the bulb at 20.0C is 0.004 50 (C)-1 and the resistance increases linearly with increasing temperature, what is the final operating temperature of the filament?
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?