Given that the live load is twice the dead, determine the maximum total service load that can be applied on a double-channel shape 2C9×15 (A992). Use ½" dia. bolts. Refer Fig. 2 for detailing. -2"+ 3"+ 3" + 3"+ 3"– 3" F

Given that the live load is twice the dead, determine the maximum total service load that can be applied on a double-channel shape 2C9×15 (A992). Use ½" dia. bolts. Refer Fig. 2 for detailing. -2"+ 3"+ 3" + 3"+ 3"– 3" F

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.2P

See similar textbooks

Related questions

Q: a base plate for a W12 x 87 column supporting a service dead load of 65 kips and a service live load…

A: Given:- W12 x 87 column Dead load = 65 kips Live load = 195 kips 16 inch x 16 inch concrete pier A36…

Q: For the eccentric shear loading of the accompanying figure, two vertical lines of % inch diameter…

Q: 6.0 The tension member shown is an L150 × 87.5 x 8. The bolts are 19 mm in diameter. If A36 steel is…

Q: For the A36 steel bracket plate of the accompanying figure, calculate the maximum service load P…

Q: A W18 × 119 is used as a compression member with one end fixed and the other end fixed against…

A: A) Calculation of slenderness ratio: KLr=1.2(12×12)2.69in.in.KLr=64.24Calculation of bulking…

Q: A restrained beam is loaded as shown below. Determine the end moment at wall A (MA). 40KN IM Select…

Q: A Channel C6x13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using…

A: Data Given: Channel Section = C6×13Bolt Diameter = 58 inchFy = 36 ksiFu = 58 ksiAg = 3.81 in2U =…

Q: Question 8: (Consider tension member only; assume gusset plate design is adequate) A double-channel…

A: We have to determine the value of factored tensile load that can be applied to the section as shown…

Q: A double-channel shape, 2C8 x 18.75 is used as a tension member. The channels are bolted to a ⅜ -…

A: LFRD was created to increase the safety and effectiveness of the design. The factor of safety and…

Q: A double-channel shape, 2C8 x 18.75 is used as a tension member. The channels are bolted to a 38 -…

Q: An angle L150 x 90 x 12 of AS72 steel (F,= 350 MPa and F= 450 MPa) is used as tension member…

A: Given: Angle section: L150 x 90 x 12 of A572 steel g = 50 mm, for 150 mm leg is connected fy = 350…

Q: Select the lightest W310 section available to support working tensile loads of 533 kN dead load and…

Q: Problem 05 -L7x 4 x을 Use A36 steel and 3/4-in Ø bolts 3 in 24 in 3 in 1 tt t - 2 in

A: Tensile strength is the dimension of the amount of force acting on a particle to pull. LFRD is to…

Q: A tension member is an L 150x90x8 connected to an 8-mm-thick gusset plate with 6-020 mm diameter,…

A: Answer We are given L 150 x 90 x 8 gusset plate thickness = 8 mm Fy = 248 Mpa Fu = 400 Mpa Bolt…

Q: A plate 3⁄8 3 6 is used as a tension member to resist a service dead load of 12 kips and a service…

A: It is required to determine the factored load using LRFD method. Pu=1.2DL+1.6LL=1.212+1.633=67.2…

Q: check the adequacy of W10 x 60 section to resist a service tensile load that induce the following…

A: Answer We are given W 10 x 60 Dead Load PD =180K Earthquake load E=147.1 Live load PL=205K Gauge g…

Q: 1. Select the lightest W12 section available to support a dead load of 810 kN and a live load of…

A: Given, DL=810 KN LL=1235 KN Length of member=6.5 m Diameter of bolt=db=20 mm A572 Grade 55 steel…

Q: SITUATION IV: A tension member is shown below and s subjected to a dead load of 15 kN and a live…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: 6.2 The vertical steel bar shown is 3/8 in. thick and must be designed to withstand a tensile load…

Q: Design a 9-ft single-angle tension member to support a dead tensile working load of 30 k and a live…

A: given data dead load=30kips live load=40kips bolt diameter=7/8 in use A36 steel fy=36ksi and…

Q: 2. Design a 2.7-m single-angle tension member to support a dead tensile working load Of 130 kN and a…

A: The given data is shown below: Length=2.7 mDead load=130 kNLive load=170 kNDiameter of bolt=22 mmA36…

Q: Problem 5: A double-angle tension member, 2L 76 × 51 × 6.4 LLBB (Longer legs are connected back to…

A: Given Gross area =1.2 in2 Dead load =15 kN= 3.372 kips Live load= 6kN=1.3488 kipi

Q: A tension member with a length of 22 feet must resist a service dead load of 216 kips and a service…

A: You didn't specify which method to use. I have solved using LRFD.

Q: A C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown in Figure P3.2-3. If Fy =…

A: The design strength is reduction in the actual resistance of the member while considering the factor…

Q: A tension member with a length of 6 feet must resist a service dead load of 22 kips and a service…

A: Rectangular c/sDL = Dead load = 22 kipsLL = Live load = 55 kipsL = Length of member = 6 ft = 6×12 =…

Q: Problem 1: For the WT8x50 attached through the flange to a 12x34 inch plate with eight 7/8 inch…

A: Solution: Given: Section: WT 8 x 50 A = 14.70 in2 y = 1.760 in bolt = 7/8 in s = 3 in

Q: Determine the critical net area of the L152 × 89 × 7.9 tension member shown with staggered 22-mm…

Q: Fy= 50 Ksi, Fu= 65ksi Select the lightest W10 section available to support working tensile loads of…

A: Given : Fy= 50 Ksi, Fu= 65ksi Select the lightest W10 section available to support working tensile…

Q: Q2: Determine the load capacity of a C8 x 11.5 tension member connected to a (3/4 in.) gusset plate…

A: Given, C8×11.5 Area of the gusset,Ag=3.37 in2 The thickness of the plate,tw=0.22 in fy=50 ksi…

Q: Q1/ A tension member with a length of 6ft 3in must resist a service dead load of 60k, a service live…

A: Solution Given Data Length= 6'3" Service dead load= 60k Service live load= 100k Service wind load=…

Q: A single angle L 65 x 50 x 5 is connected to a 10mm gusset plate with 18mm diameter bolts. The…

Q: Question 3: Four 3 x 3 x1/2 angles are used to form the member shown in the accompanying…

A: Design the end tie plates and lacing bars as shown belowDraw thr cross section of the column as…

Q: A) Find out the safe load P <arried by the joint shown in Fig. Ex. 10.1. The rivets are pPower…

Q: 3.6-5 Use load and resistance factor design and select an American Standard Channel shape to resist…

A: The given values are as follows The factored tensile load=180kipsThe length =15ftThe shear lag…

Q: An ASTM A992 WT6-section is to be used to resist a dead load of 310 kips and a live load of 425 kips…

Q: Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown…

A: Given : PD =200K PL = 320 Member length = 30ft U = 0.85

Q: Determine the lightest W 12 (A36) section suitable for a 8 m long W-shape member to carry an axial…

A: Solution Given: A36 steel fy = 36 ksi = 250 MPa fu = 500 MPa db = 20 mm P = 1900 kN

Q: Select a 9-m long W10 section of A572 Grade 50 steel to support a tensile load of PD = 490 kN and PL…

Q: 5.2 For the calculation of net area of flat with staggered bolts, the area to be deducted from gross…

Q: A WT 8×13 of A992 steel is used as a tension member. The connection is with 7/8-in. diameter bolts…

Q: 4. Select the lightest W14 section available to support service tensile loads Po = 445KN and P = 667…

A: Introduction- When a structure, or any member or element, is subjected to acceptable combinations of…

Q: Use load and resistance factor design and select the lightest American Standard Channel shape to…

Q: 1- A double angle section with unequal legs (200x100×12), long legs back to back is connected to a…

Q: Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter.…

Q: Select a 30-ft long W12 section of A992 steel to support a tensile service dead load of 130 kips and…

A: Limit state design For Limit state design load factor expressions are: Pu = 1.4 D and Pu = 1.2 D +…

Q: A built-up section consists of two channels (C 300 x 37) and two steel plates 12.52 x 300mm bolted…

Q: 3-27. AW18X 40 consisting of A992 steel and having two lines of 1-in Ø bolts in each flange. There…

Q: A36 (Fy=36ksi; Fu=58ksi) steel is used for the tension member shown. a. Determine the design…

Q: Compute the effective net area of the built-up section shown in Fig. P3-19 if the holes are punched…

A: Calculation of net area (An): The given member of C10x25 is given below:

Q: 1. A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset…

A: Adequacy of the given tension member,

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

Problem #2
Given that the live load is twice the dead, determine the maximum total service load
that can be applied on a double-channel shape 2C9×15 (A992). Use ½" dia. bolts. Refer
Fig. 2 for detailing.
- 2"+ 3"-
-3".
-3"
-3"
F
Fig. 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown in Figure P3.2-3. If Fy = 50 ksi, Fu = 65 ksi, and Ae = 0.90An, compute the following. a. The design strength for LRFD. b. The allowable strength for ASD.
A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate with four 5 ⁄8-inch-diameter bolts as shown in Figure 1. Assume that the effective net area Ae equals the actual net area An. (a) Calculate the design strength for LRFD? (b) Calculate the allowable strength for ASD?
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
A C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown. If Fy = 50 ksi, Fu = 65 ksi, and Ae = 0.90An, compute the following. a. The design strength for LRFD. b. The allowable strength for ASD.
Two steel plate tension members have been connected using 0.72 inch diameter bolts arranged in an equally-spaced 9 by 3 rectangular formation. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 51.2 ksi, clear distance for each edge bolt as 0.12 in, and the clear distance for the other bolts as 1.072 in. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load and live load assuming live load is half as much as dead load. Consider ASD.
A single-angle tension member 175 mm x 100 mm x 18 mm haw two gage lines in its long leg and one in the short leg for 16 mm bolts arranged as shown. Area of the angular section is 4961 mm^2. Use A36 steel Fy = 248 MPa and Fu = 400 MPa. Standard nominal hole diameter for 16 mm bolt = 17 mm. Determine the net area of the angular section. Determine the allowable tension strength of the angular section based on the gross area. Determine the allowable tensile strength of the angular section based on the effective net area. Reduction factor U = 0.75
A 2L 3 x 2 x ¼ LLBB tension double angle, A36 steel is subjected to a dead load of 12 kips and a live load of 36 kips. It is attached to a gusset plate with a line of 3/4-inch diameter bolts through the long legs. Does this member have enough stamina? Assume Ae= 0.85 in. Use LRFD.
A bracket must support the service loads shown in the figure below. The loads act through the center of gravity of the connection. The connection to the column flange is with eight 7/8-inch diameter, A325N bolts. A992 steel is used for all components. Is the connection adequate? Use LRFD. Show all work to verify the bearing strength and the combined effects from tension and shear in the bolts. Ignore any potential prying action created in the WT.
A channel shape, C8 × 18.75, is used as a tension member. The channels are boltedto a 10mm-thick gusset plate with 22mm- diameter bolts. The tension member is A572 Grade 50 steel (Fy = 345 MPa, Fu = 450 MPa) and the gusset plate is A36 (Fy = 250 MPa, Fu = 410MPa). What is the ult. capacity of the gusset plate in kips, if block shear governs? What is the effective net area of the channel section, in square millimeters?
An ASTM A992 WT6-section is to be used to resist a dead load of 310 kips and a live load of 425 kips in tension. The section is connected by 1/2-inch bolts in standards holes on its flange to a plate, as shown below. The distance of the bolts from the end and the edges of the tension member are fixed. The member is 8 ft long. Use LRFD approach. Determine the minimum required effective net area of the section, in in^2 Determine the minimum required gross area of the section, in in^2
A channel shape, C8 × 18.75, is used as a tension member. The channels are boltedto a 10mm-thick gusset plate with 22mm- diameter bolts. The tension member is A572 Grade 50 steel (Fy = 345 MPa, Fu = 450 MPa) and the gusset plate is A36 (Fy = 250 MPa, Fu = 410MPa). What is the ult. capacity of the channel in kips, if yielding on the gross area governs? What is the ult. capacity of the channel in kips, if fracture on the net area governs?
Determine: a. max allowable Pu if the shearing if 0.5in bolts dia. governs b. max allowable Pu if the bearing of the tension member governs c. max allowable Pu if all "actions" are considered d. number of anchor bolts needed if an A992 steel bolt is used instead of A325. Assume force is equally shared by the bolts, and the anchor bolts are properly bonded on the ceiling