I hope the tutor will give a detailed and clear answer Given the beam shown below, determine the shear force and bending moment at point C. Given the dimensions a = 2.2 m, b = 6.4 m and c = 2 m, and theload intensities e = 10.5 kN/m and f = 4 kN/m.e kN/mf kN/mambmcmDABCShear force (observe the up on the left, down on the right positive sign convention):SFC = 数字单位(tolerance 0.2 kN)Bending moment (observe the sagging positive sign convention):BMC =单位(tolerance 1 kN*m)

Answered: Image /qna-images/answer/8123b841-9f55-40b0-b25e-e646a4596f70.jpg

Answered: Given the beam shown below, determine…

Given the beam shown below, determine the shear force and bending moment at point C. Given the dimensions a = 2.2 m, b = 6.4 m and c = 2 m, and the load intensities e = 10.5 kN/m and f = 4 kN/m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

determine the diagram of the shear forces and bending moments in the beam shown below. Data P = 20kN, M = 60kNm, q = 10kN / m, a = 5m, b = 2m, c = 3, alpha = 60.
Give the expression for the shear force, V = V(x), and the bending moment,M = M(x), as a function of the distance, x, measured from point A.Hint: Find the expressions of shear force and bending moment in each section:AB (0< x <4), BC (4 <x <7) and CD (7< x <10)
Determine the maximum positive normal bending stress that occurs in member ABC of the engine crane given the following information: Engine weight = 1500 lb Member ABC height (vertical cross sectional dimension) = 7 in Member ABC width (horizontal cross sectional dimension) = 1 in Express your answer to the nearest whole psi value. In your work, draw the shear and moment diagram for member ABC. For the question above, determine the maximum shear stress in member ABC that occurs between points A and B. Express your answer using the nearest whole psi value.
Consider that the section is transmitting a positive bending moment about the z axis,Mz, where Mz=10 kip*in if the dimensions of the section are given in ips units, or Mz=1.13kN*m if the dimensions are in SI units. Determine the resulting stresses at the top and bottom surfaces and at every abrupt change in the cross section. Find the second moment of area, the location of the neutral axis, and the distances from the neutral axis to the top and bottom surfaces.
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear in kN. 3. Determine the location of Neutral Axis, in mm, from the top of the section. 4. Determine the location of the centroid, in mm, from the left of the section. 5. Determine the moment of inertia of the section in x106 mm4 . 6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa. 7. Determine the maximum flexural stress experienced by the beam in MPa. 8. Determine the maximum shearing stress in MPa at Neutral Axis. 9. Determine the spacing of rivets in mm. 10. Determine the maximum flexural stress at 1 m from the support at D to E in MPa.
a) 1. The support reaction forces at the A and C, in terms of P,be careful of the sign. 2. Give the expressions of the shear and moment at an arbitrary poistion x of AB segment, in terms of P and x, be careful of the sign. 3. Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, in terms of P and x, be careful of the sign. b)Given l= 1000 mm, P= 4000 N and l1/l=0.66, calculate the internal shear force and draw the moment diagram
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
Determine the internal forces (axial force, shear force, and bending moment) at point j of the indicated structure, teta = 0 º
Calculate the internal shear force and the internal bending moment for the beam at every point x, and sketch the shear and moment diagrams. At what point in the beam (x=?) does the maximum normal stress occur? Find the maximum normal stress, 0 , due to bending, At what point in the cross section (y=?) does the maximum normal tensile stress occur?? Find the magnitude of the maximum transverse shear stress on the cross section, T, due to bending at the point “A”. At what point in the cross section (y=?) does the maximum transverse shear stress occur?
Draw the shear force diagram and bending moment diagram for the loaded cantilever beam as shown in figure. Mark all salient point in the diagram. Neglect the self-weight of the beam. Where P=3m, Q=2m, R=3m, S=3m, F1=20 N, F2=10N, U=15N/m. (i) The reaction at A (unit is in N) = ___________ (ii)Shear force at "A" (Unit is in N) =_______________ (iii)Shear force at "B" (Unit is in N) =_______________ (iv)Shear force at "C" (Unit is in N) =_______________ (v) Shear force at "D" (Unit is in N) =_______________ (vi) Shear force at "E" (Unit is in N) =_______________ (vii) Bending moment at "E" (unit is Nm) = __________ (viii) Bending moment at "D" (unit is Nm) = __________ (ix) Bending moment at "C" (unit is Nm) = __________ (x) Bending moment at "B" (unit is Nm) = __________ (xi) Bending moment at "A" (unit is Nm) = __________