Given the circuit below, which of the below value(s) would change if the inductance value were doubled? Assume the circuit has been in thisposition for some time prior to the switching event happening.Multiple correct answers may exist. Select any/all that apply!t=03012 V (+3H20240:energy stored prior to the switching eventinductor current initial conditiontime constantenergy stored when the system reaches steady-stateinductor current final conditionNone of these answers are correct402

Formula to calculate iL(t) is: iL(t)=i(∞)+i(0+)-i(∞)e-tTwhere, T is time constantT=LRi(0) is initial…

Given the circuit below, which of the below value(s) would change if the inductance value were doubled? Assume the circuit has been in this position for some time prior to the switching event happening. Multiple correct answers may exist. Select any/all that apply! iz(1) 30 12 V 3H 202 1=0 ملم 402 energy stored prior to the switching event inductor current initial condition time constant energy stored when the system reaches steady-state inductor current final condition None of these answers are correct 403

Given the circuit below, which of the below value(s) would change if the inductance value were doubled? Assume the circuit has been in this position for some time prior to the switching event happening. Multiple correct answers may exist. Select any/all that apply! iz(1) 30 12 V 3H 202 1=0 ملم 402 energy stored prior to the switching event inductor current initial condition time constant energy stored when the system reaches steady-state inductor current final condition None of these answers are correct 403

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PA: You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor...

See similar textbooks

Similar questions

A heart defibrillator is used to resuscitate an accident victim by discharging a capacitor through the trunk of her body. A simplified version of the circuit is shown . (a) What is the time constant if an 8.00-μF capacitor is used and the path resistance through her body is 1.00×103 Ω ? (b) If the initial voltage is 10.0 kV, how long does it take to declineto 5.00×102 V ?
a) What is the coupling constant between the two coils?b) Using the dot notation, determine if the induced voltages are additive or subtractive?c) Write the expressions for V1(t) and V2(t).d) Using KVL, determine the differential equation needed to solve for I2(t).e) Solve the differential equation in part d to get I2(t). Assume no energy stored in inductors at t=0.f) Use I1(t) and I2(t) to determine V1(t) and V2(t).
For a Second Order Damped system, the damping rate is ζ=0.58 and its natural frequency is ωn=55rad/sise; How many seconds is the peak time in the unit-digit response applied to the system?
The following parameters are used in an EDM process, the supply voltage is 150V. The resistance and capacitance in the circuit are 50 Ohms and 15 microfarads respectively. The tool is made of brass and kerosene is used as the dielectric. A hole diameter of 20 mm is to be cut into a plate of thickness of 3mm. If the discharge takes place at maximum power conditions. The value of constant K4=0.18, calculate the MRR, and machining time.
Show your complete solution and attached it here. Answer must be in 4 decimal places. An industrial coil is modeled as a series combination of an inductance L and resistance R. Since an ac voltmeter measures only the magnitude of a sinusoid, the following measurements are taken at 60 Hz when the circuit operates in the steady-state: |Vs| = 145 V, |V1| = 50 V, |Vo| = 110 V Use these measurements to determine the values of L and R.
Please answer ASAP and I'll upvote, thank you. In the given circuit, switch S1 is in position A and switch S2 is open. Both switches are in these states for a very long time. At t=0, switch S1 moves from position A to B while switch S2remains open. 10ms after switch S1 moves to position B, switch S2 is closed and remains closed for 20ms only. Determine the expressions for the inductor current for 0≤t<10ms, 10ms≤t<30ms, 30ms≤t<∞, and determine the time (in ms) after switch S1 moves to position B is the current in the inductor equivalent to 30% of the initial value (at ?=0).
COURSE: Electrical EngineeringSUBJECT: Electrical ApparatusINSTRUCTIONS:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units• Round up to 3 three decimal places the FINAL ANSWERS and BOX it. PROBLEM:A capacitor in series with a 66 Ω resistor is connected to a 120 V, 60 Hz source. If the impedance of the circuit is 116 Ω, determine the size of the capacitor.
Given the circuit below with the switch closed for a long time, then opening at t=0, and with the values R1=193KΩ, R2=186KΩ, R3=107KΩ, calculate the capacitor voltage at t =0.
If a circuit consisting of a resistor and induction in series has a DC current of 500mA following through it, andthe switch in the circuit is suddenly open. What is the Inductive spike voltage induced in the inductor if thecurrent reaches 0 A in 200 x 10-6 sec (200 micro second) and the Inductance, L =100mH? Hint: { Vemf =L di/dt}a) 250 V b) 500 V c) 1000V d) 10 V
For the sequential circuit shown in Figure, the current flowing through the inductor is zero. At t = 0, the switch moved from position a to b, where it remained for 1 s. After the 1 s delay, the switch moved from position b to position c, where it remained indefinitely. Sketch (plot) the current flowing through the inductor versus time.
All capacitors were initially discharged. at t = 0, S1 is placed at position 1 and S2 is closed. At t = 15 ms, S1 is placed at position 2 and S2 is kept closed. During this phase, it has been determined that the total resistance seen by the equivalent capacitor is 28 kΩ; and that vT = 10 V at t = 15 ms. Calculate the value of the current iT immediately after the switching occurred. Enter your answer in mA rounded to 2 decimal places. At t = 25 ms, S1 is kept at position 2 and S2 is opened. Data: R1 = 6.5 kΩ, R2 = 10 kΩ, R3 = 1.0 kΩ, R4 = 4 kΩ, R5 = 20 kΩ, R6 = 11.5 kΩ; C1 = 4.5 µF, C2 = 4.0 µF, C3 = 12 µF
For t >0 in the given figure, determine the time t at which i = 2.0 A, assuming DC steady state for t < 0. The time t when the current assumes the steady-state value is _______ ms.