Answered: Given the ff: w=67% Gs=2.67…

Engineering

Civil Engineering

Given the ff: w=67% Gs=2.67 Gwet=19.89kN/m3. What is the degree of saturation

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter2: Soil Deposits-origin, Grain-size, And Shape

Section: Chapter Questions

Problem 2.4P: For a soil, given: D10 = 0.08 mm D30 = 0.22 mm D60 = 0.41 mm Calculate the uniformity coefficient...

See similar textbooks

Related questions

Q: A basketball match is to be held in a coliseum with a seating capacity of 2,500. Three types of…

Q: Find the reaction at both supports. 11. Identify the maximum moment. 12. Determine the maximum…

Q: A 200 mm wide concrete block wall carries a vertical dead load of 120 kN/m and a verticallive load…

A: Given data:- Width of concrete block wall = 200 mm Vertical dead load = 120 kN/m Vertical live load…

Q: The grade of the concrete is M25. Find the values of design strength in- 1. Direct Compression. 2.…

A: Given data- Grade of concrete-M25To Find-design strengths

Q: What are the recommended rates of data collection in a rapid static survey?

A: Static Survey:- A relative positioning method called "static surveying" uses two or more fixed…

Q: The pseudo-spectrum is associated with: a) pseudo-speed b) pseudo-acceleration c)…

Q: an

Q: Determine the degree of indeterminacy of the structure below 02

Q: Question 2 Refer to the given figure below. Given: a = 1.55 m b=1.11 m c=0.73 m Carbon…

Q: (b) A circular cylinder is placed in a uniform flow with its axis perpendicular to the flow…

A: Given- circular cylinderdrag force per unit length = FDflow velocity=Vfluid density=ρfluid…

Q: Compute the specific speed for a pump operating at 4000 rpm delivering 600 gal/minof water at a…

A: Given,The operating speed is,N=4000 rpmThe flow rate is,Q=600 gal/minTotal head is,H=150 ft

Q: Estimate the cost of constructing a cell site and include all costs along with their associated…

A: Cell Site : A cell site is a cellular enabled mobile device site where the electronic communication…

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B…

Q: 7. A cylinder of radius 0.661m is rotated about its axis at 261 rev/ min. If the cylinder is 16.1%…

Q: Engineering Utilities Please answer in paragraph form. UPVOTE will be given. What are the tools…

A: Well, there are numerous tools and equipment's which are powered by compressed air. Many individuals…

Q: A center-point loading flexural test was performed on a concrete beam with across section of 100 mm…

A: b=100mm d=100mm

Q: 6.59 A square section as shown in the figure below is subjected to bending moment M. H (a) Obc = Obt…

A: Given figure: Subjected to bending moment.

Q: Each Member of the truss is a uniform 20-ft bar weighing 400 lb. Calculate the average tension or…

A: Given that :

Q: Why is a linear calibration curve important? Couldn't interpolation be used to predict values…

A: Linear calibration curve can be described as a positive sign of assay performance within a validated…

Q: According to the researchers, despite the numerous beneficial properties and benefits of timber…

A: Wood is a hygroscopic material. It takes in moisture from the air and the moisture content in the…

Q: . All dimensions are in mm (Hint: All centroids on the left and below the positive x and y axes will…

Q: 50. Find the angle between to vectors P = -2i+3j and Q = 3i-j a. 37.875* b. 52.125 c. 127.875 d.…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Yield Strength : Yield strength is a maximum stress a structure can bear beyond the maximum stress…

Q: Compute the potential evaporation for Amsterdam for the month of July if net radiation is 361 W/sqm,…

Q: Moving to another question will save this response. Question 10 Refer to the the flow shown in the…

Q: for sew A the a bove and lim pinjointed and joints. Stiffness also la portal frame, tixed at at 'D',…

A: Frame : A frame is a structure which has combination of beam, column and slab which resist the…

Q: Use the virtual work method to determine the vertical deflection and the horizontal deflection at…

Q: Determine the deflection at point B given the cross-section of the beam and assuming E = 200 GPa. A…

A: Macaulay's method is the most common method used in structural analysis to determine the deflection…

Q: 1. A line is recorded as Am long. It is measured with a (E÷200)kg tape (Bm full tape length) which…

A: Surveying: It is an art of determining the relative position of points on above or below the surface…

Q: Determine the degree of indeterminacy 01 0⁰ O 3 O 4 of the structure below P

Q: find cg and Ix and ly and Ixy ~ 15cm, 100m isan 40 cm 30cm 200m

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: f 1 MB.) Design headwater elevation (ELhd) = ation of stream bed at face of invert = 99.55 ft…

A: Data given:Flow rate = 200 ft3/sec.Ke = 0.5Design headwater elevation (ELhd) = 105 ft.Elevation of…

Q: I need this answer handwritten mention question number also and please on white page I'll UPVOTE for…

A: Solution: The given problem is symetrical section with symmetrical loading: Hence it is enough to…

Q: G 0.85), find the total energy head (m) at point A with respect into a datum at the pump. Suction…

A: According to given dataThe solution of the problem is given belowThe Energy Head would be -4.40…

Q: 1. 26.1% of the surface area of the spherical buoy is submerged in water. Find the specific gravity…

Q: A W L/2 L/2

Q: Check for the control of deflection for a really supported a hundred and twenty mm thick slab is…

Q: Consider the tank shown in the figure. The gate is rectangular in shape with width into the paper of…

Q: he given struc

A: Take reaction at B as redundant :Deflection due to reaction =RBL33EIupDeflection due to load…

Q: A soil has bulk density of 21.36 kN/m3 and water content of 18.90%. Calculate the water content (in…

Q: Q2) Draw contours of 13m, 19m and 30m by interpolation method, with suitable scale. RLs at corners…

Q: 24). A circular curve is to be set out between two straight lines ngle (I= 12°40'), the station of…

A: Given I=12040'R=2900

Q: W L/2 L/2 B

Q: An RCC structure with fundamental time period of 1.2 sec vibrates at a forcing frequency of 10…

A: Given- time period T=1.2 sTn=1.25ω=10 rad/s

Q: Situation 3: The cable shown supports a horizontal uniform load of 10 kN/m. Determine the:

A: Answer Let us draw free body diagram of the forces acting on the cable (1) Calculation of Tension…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

A: According to given dataThe maximum principal stress experienced on the shaft will be175.43…

Q: 2.) For the shape shown to the right: in. plate C5x9 steel -L2x2x¹ steel Find: a.) Find the centroid…

A: Given A composite section Required Centroid location Moment of inertia about centroidal x axis

Q: Two wastewater streams A and B, having an identical ultimate BOD are getting mixed to form the…

Q: A structure is to be built with concrete with a minimum dimension of 0.2 m, minimum space between…

A: Given:- minimum dimension=0.2mm minimum space between rebars=40mm minimum cover over rebars=40mm Two…

Q: On this figure, what is the minimum value of P to move the 40 N block? Assume that the coefficient…

A: Given coefficient of friction between two blocks is 0.25 and 0.333 for floor surfaces. Required…

Concept explainers

Principles of Seepage

In hydrology, when water flows down in a pore or crack of unsaturated soil due to gravity, the deep layer of soil is called seepage. It is the slow movement of water in the soil layer. Seepage is mainly found near hydraulic structures and is responsible for the stability of earthen-type hydraulic structures.

Question

100%

Given the ff:

w=67%

Gs=2.67

Gwet=19.89kN/m3.

What is the degree of saturation?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the degree of Saturation at the above conditions ?
. A natural soil deposit has a bulk unit weight of 18.44 kN/m3and water content 5%. Calculated theamount of water required to be added to 1 m3soil to raise the water content to 15%. Assume thevoid ratio remains constant. What will then be the degree of saturation? Take Gs as determined inquestion no. 2. G=2.69
Determine the degree of saturation in percent. a. 86 b. 15.97 c. 20 d. 41
A concrete dam retains water to a height of 9 m. It has rows of sheet piling at both heeland toe which extend half way down to an impervious stratum. From a flow net sketchedon a transformed section, it is found that there are four flow channels and sixteen headdrops. The average horizontal and vertical permeabilities of the soil are 6 × 10^–3 mm/sand 2 × 10^–3 mm/s, respectively. What is the seepage in cubic meter per day, if the lengthof the dam is 150 meters?
In a constant head permeameter with cross section area of 10cm2 when the flow was taking place under a hydraulic gradient of 0.5. the amount of water collected in 60seconds is 600cc.find the permeability of soil.
A clay layer 5 m thick has double drainage. It was consolidated under a load of 127.5 kN/m2. The load is increased to 197.5 kN/m2. The coefficient of volume compressibility is 5.79 × 10^–4 m2/Kn and value of k = 1.6 × 10^–8 m/min. Find settlement in cm at 50% consolidation. a.25.78 b.10.32 c.32.56 d.20.27
A layer of silty soil of thickness 5 m lies below the ground surface at a particular site and below the silt layer lies a clay stratum. The ground water table is at a depth of 4 m below the ground surface.The following data are available for both the silt and clay layers of soil.Silt layer: ?10 = 0.018 mm, e = 0.7, and Gs = 2.7Clay layer: e = 0.8 and Gs = 2.75Required: (a) Height of capillary rise, (b) capillary pressure, (c) the effective pressure at the ground surface, at groundwater table (GWT) level, at the bottom of the silt layer and at a depth of H =6 m below ground level, and (d) at a depth 2 m below ground level. (Sketch or draw the stress distribution diagram).
Explain the term degree of saturation and how it is expressed in percent.
A layer of silty soil of thickness 5 m lies below the ground surface at a particular site and below thesilt layer lies a clay stratum. The ground water table is at a depth of 4 m below the ground surface. The following data are available for both the silt and clay layers of soil. Silt layer: ?10= 0.018 mm, e= 0.7, and Gs = 2.7 Clay layer: e = 0.8 and Gs = 2.75 Required: (a) Height of capillary rise, (b) capillarypressure, (c) the effective pressure at theground surface, at groundwater table (GWT)level, at the bottom of the silt layerand at a depth of H =6 m below groundlevel, and (d) at a depth 2 m below ground level.(Sketch or draw the stress distribution diagram).
Compute the capillarity of mercury with a specific gravity of 13.6 in a 2-mm diameter tube. Assume a cohesion of 0.467 N/m and contact angle = 140°. Indicate whether it is a rise/ fall.
A layer of silty soil of thickness 5 m lies below the ground surface at a particular site and below thesilt layer lies a clay stratum. The ground water table is at a depth of 4 m below the ground surface.The following data are available for both the silt and clay layers of soil. Silt layer: ?10= 0.018 mm, e= 0.7, and Gs = 2.7Clay layer: e = 0.8 and Gs = 2.75Required: (a) Height of capillary rise, (b) capillarypressure, (c) the effective pressure at theground surface, at groundwater table (GWT)level, at the bottom of the silt layerand at a depth of H =6 m below groundlevel, (d) at a depth 2 m below ground level.(Sketch or draw the stress distribution diagram).
Answer the following questions!a. What is the definition of Archie's Equation?b. What is Archie's Law of Saturation Equation?