Given the following branch instruction and location, answer the following questions about it. Address Instruction Ox10000 Oxb5000184 What type of Branch instruction is this (CBZ, CBNZ, B, etc.): What is the offset in instructions of the branch target (write as a hex number with "-" if negative): What is the offset in bytes of the branch target (write as a hex number with "-" if negative):

Given the following branch instruction and location, answer the following questions about it. Address Instruction Ox10000 Oxb5000184 What type of Branch instruction is this (CBZ, CBNZ, B, etc.): What is the offset in instructions of the branch target (write as a hex number with "-" if negative): What is the offset in bytes of the branch target (write as a hex number with "-" if negative):

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter3: Hardware: Input, Processing, Output, And Storage Devices

Section: Chapter Questions

Problem 3SAT: The time it takes to perform the fetch instruction and decode instruction steps is called the...

See similar textbooks

Similar questions

The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
Will upvote! Find the memory address of the next instruction executed by the microprocessor, when operated in the real mode, for the following CS:IP and 80286 register combinations: a. DS=2F2E & DX=9D64 b. CS=9F7A & IP=AB27 c. ES=DE21 & DI=D75F d. SS=FF5C & BP=92B8 e. DS=DC67 & CX=2FE8
What are the values of ECX, EBP, and ESP registers after executing the following instruction? push ECX Before ECX: 0xBABE EBP: 0x0012FF24 ESP: 0x0012FF24 After ECX: EBP: ESP:
Write an assembly code to implement the y = (x1+x2) * (x3+x4) expression on 2-address machine, and then display the value of y on the screen. Assume that the values of the variables are known. Hence, do not worry about their values in your code. The assembly instructions that are available in this machine are the following: Load b, a Load the value of a to b Add b, a Add the value of a to the value of b and place the result in b Subt b, a Subtract the value of a from the value of b and place the result in b Mult b, a Multiply the values found in a and b and place the result in b Store b, a Store the value of a in b. Output a Display the value of a on the screen Halt Stop the program Note that a or b could be either a register or a variable. Moreover, you can use the temporary registers R1 & R2 in your instructions to prevent changing the values of the variables (x1,x2,x3,x4) in the expression. In accordance…
333: E8B3 8B3: 0A12 A12: 2153 Since the contents of the relevant addresses are 333 in the basic computer given above, the initial value of the PC is 333; When fetching and executing an indirectly addressing ISZ instruction, write the contents of the following registers in hexadecimal (hex) format for the T5 time. AR ........... DR......... IR ........... PC ........... SC ...........
Compute the physical address for the specified operand in each of the following instructions from previousproblem. The register contents and variables are as follows : (CS) = 0A0016, (DS) = 0B0016, (SI) =010016, (DI) = 020016 and (BX) = 030016.a) Destination operand of the instruction in (c)b) Source operand of the instruction in (d)c) Destination operand of the instruction in (e)d) Destination operand of the instruction in (f)e) Destination operand of the instruction in (g)
Single instruction computer (SIC) has only one instruction that for all operations our MIPS does. The instruction has the following format. sbn a, b, c # Mems[a]=Mem[a]- Mem[b]; if (Mem[a]<0) go to PC+c For example, here is the program to copy a number from location a to location b: Start: sbn temp, temp, 1 sbn temp, a, 1 sbn b, b, 1 sbn b, temp, 1 So build SIC program to add a and b, leaving the result in a and leaving b unmodified.
Consider the following instruction:Instruction: Add Rd, Rs, RtInterperation: Reg[Rd] = Reg[Rs] + Reg[Rt] RegWrite MemRead ALUMux MemWrite ALUOp RegMux Branch a, What are the values of control signals generated by the control in Figure 4.2 for the above instruction? b, Which resources (blocks) perform a useful function for this instruction? c, Which resources (blocks) produce outputs, but their outputs are not used for this instruction? d, which resources (blocks) produce no output for this instruction?
1. T/F - if (B)=006000 (PC)=003600 (X)=000090, for the machine instruction 0x032026, the target address is 003000.2. T/F – PC register stores the return address for subroutine jump.3. T/F – S register contains a variety of information such as condition code.4. T/F – INPUT WORD 1034 – This means Operating system should reserve 1034 bytes in memory5. T/F - In a two pass assembler, adding literals to literal table and address resolution of local symbol are done using first pass and second pass respectively.
In the Intel 8086 microprocessor, suppose the register AX contains the data 35AB H. What will be the contents of AX after executing the following programs? Assume that the initial content on the Carry Flag (CF) is one for all the calculations. You MUST clearly show ALL your steps in obtaining your final result for getting full and/or partial credit. Please present your final result in Hexadecimal format. (a) MOV CL,04H SHR AX,CL RET (b) MOV CL,04H RCR AX,CL RET
Problem Given the following memory values and a one-address machine with an accumulator, what values do the following instructions load into the accumulator? Word 20 contains 40. Word 30 contains 50. Word 40 contains 60. Word 50 contains 70. LOAD IMMEDIATE 20 LOAD DIRECT 20 LOAD INDIRECT 20 LOAD IMMEDIATE 30 LOAD DIRECT 30 LOAD INDIRECT 30
What happens if an instruction is written to VA page 30 before it has been approved? In the following contexts, a TLB that is maintained by software would be more efficient than one that is handled by hardware: