Given the Frame as shown below. Using Method of Members, determine the following if the External Load F is equal to the magnitude of the x – component of reaction B (F =B,). a.) The External Reaction at Point A. b.) The External Reaction at Point B. c.) The Internal Reaction at Point C. 1m F 1.5 m 1 m В 60° 400 N/m

Given the Frame as shown below. Using Method of Members, determine the following if the External Load F is equal to the magnitude of the x – component of reaction B (F =B,). a.) The External Reaction at Point A. b.) The External Reaction at Point B. c.) The Internal Reaction at Point C. 1m F 1.5 m 1 m В 60° 400 N/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use Analysis of Frame by Method of MembersNote: h = 1m
Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is ± 2.50% Relative to the right answer. 1.) The reaction @ point D 2.) The tension @ Cable BE. 3.) The x-component of the reaction @ A. 4.) The y-component of the reaction @A 5.) The reaction @ A.
GIVEN: L1=20 N GIVEN: a= 4m GIVEN: L2= 20 N GIVEN: b= 5m GIVEN: L3=20 N GIVEN: c= 6m GIVEN: L4= 0 N GIVEB: e= 3m GIVEN: L5= 10 N ANSWER: (a) Ax in N (b) Ay in N (c) Ex in N (d) Ey in N PLS SOLVE IN A COMPLETE SOLUTION AND WRITE LEGIBLY AND ALSO DRAW THE FREE BODY DIAGRAM
A single bar has 3 different cross sections as shown below. The load P1 is equal to 25,500 Newtons and P3 is equal to 17,000 Newtons. Determine the reaction at the support at bar (3). Find the force in bar (2). Note: Final Answer in 4 decimal places.
The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG, FG by the method of joints. Show all solutions please don't skip. Please show to did u get FBC, FBE, FBD Thanks!FBDsin30-FBEsin60-FBC = 243.301KN then FBC = -625.77KN. how? please teach me how thanks!
Question-2 A trolley that moves along a horizontal beam is acted upon by two forces. Determine the magnitude and direction of the force P do that reluctant is a vertical force of 2500N. Figure:2
The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG, FG by the method of joints. Show all solutions please don't skip. Please show to did u get FBC, FBE, FBD Thanks!FBDsin30-FBEsin60-FBC = 243.301KN then FBC = -625.77KN. how?did you divide 243.301KN to sin30 + sin 60?? please write the solution down and i'll thumbs up to all ur answers thanks!
Need help asap Find the force (N) in link if θ= 0° and P = 295 N. Round off only on the final answer expressed in 3 decimal places .
The given plane truss structure below is (where truss member BD is a single member and should not be considered as 2 members) A. Statically determinate B. Statically indeterminate with redundant truss members C. Statically indeterminate with deficient truss members D. Can’t be determined
A foundation must be built on a non-cohesive soil that has the following characteristics: soil density = 18.0 kN/m3, saturated soil density = 19.0 kN/m3, internal friction angle of 30°, depth of planting = 1.5 m and depth of water table = 0.8 mThe gross allowable load with FS = 3 is 700 kN. Determine the dimensions of the proposed footing using Meyerhof theory.
Determine the horizontal displacement of joint C. The length, L, of trusses AC, BC is 1,300 mm. The applied force at joint C, is 5.0 kN. The cross-sectional area of both trusses, A, is 360 mm2. The elastic modulus of truss AC, E1, is 135 GPa. The elastic modulus of truss BC, E2, is 150 GPa.
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.