= Given the open loop transfer function G(s) such that the output settling time T, = 2. R(s)+ Determine the value of p. Choice e=0: It means "None of above" P = 08.52 01.6748 04.96 04 80 s(s+p) G(s) Select the value of p Y(s) Need neat and clean handwritten solution explaining every steps

= Given the open loop transfer function G(s) such that the output settling time T, = 2. R(s)+ Determine the value of p. Choice e=0: It means "None of above" P = 08.52 01.6748 04.96 04 80 s(s+p) G(s) Select the value of p Y(s) Need neat and clean handwritten solution explaining every steps

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the unity-feedback system with the open loop transfer function: ?(?)= 1 /?+5 Obtain the steady-state output of the system when it is subjected to each of the following inputs: a- r(t) = sin(? + 30°) b- r(t) = 2cos(2? − 45°) c- r(t) = sin(? + 30°) + 2cos(2? − 45°)
The transfer function of G(s)= s^2 +s +4/s(s-1)(s+1) is in a closed loop unit negative feedback system with a compensator of gain K. Use Nygist criterion to find the values of K for which the system will be stable and check your result using the Routh-Hurwitz criterion and a root locus plot.
Find the transfer function of the electric circuit given below by the block simplification method. In case of R = 1kΩ, C = 10µF and L = 2mH, if the system operates in closed loop with negative unit feedback, find out what the k value should be in order for the system to be stable.
The transfer function of G(s)=(s^2+s+4)/s(s-1)(s+1) is in a closed loop unit negative feedback system with a compensator of gain K. Use the Nyquist criterion to find the values of K for which the system will be stable and check your result using the Routh-Hurwitz crierion.
For the loop transfer function as G(s)H(s)=K(?+5) / s(s+6)(s+7) , determine: i. Static error coefficients. ii. What is the value of ‘K’ to make the steady-state error is 0.719 for a unity ramp input. iii. Using K=20, what is the steady-state error when the input is r(t)=1/2 ? +12
Following is an example of the forward transfer function for a system with unity feedback: Determine the error at steady state for the given inputs, which are as follows: 15u(t) 15tu(t) 15t2u(t)
A system transfer function has its poles at −2,−2 and −1± j1, and its zeros at 1,−3. (1) Determine the dominant pole(s) (Enter your response in the blank box, in the case of multiple poles: separate with commas):(2) If the system DC gain is equal to -3, build the system transfer function (Enter your response in the blank box in the form ((D + E))/((A+B)(G+H)):
Given a plant P(s)=−3s+1s+a and a model for measureable output disturbance d with transfer function Q(s)=1s+b. Compute the DC feedforward solution uP=u+Fd, where u is the feedback control, F is the feedforward gain, abd uP is the plant input, when a = 4.3 and b = 3 (use 2 decimals).
Question 03: Assuming that when applying a step r(t) = 1 at the input of a system, it presents as output the curve below, with its closed-loop transfer function given by G(s), determine: a) The values of k, b and m. b) The closed-loop and open-loop transfer function; c) The classification of the closed loop transfer function with respect to its damping. Justify!
1) y(t) = 3e-2tu(t)The function above defines the model of a signal from the braking activities of a vehicle.a)sketch the signal using the information above.b)Determine the power & energy of the signal. 2) A sensor is used to capture voltage signal y(t) from a volcanic eruption & passed through an active highpass filter system for processing.a)Make a circuit diagram sketch for the process.b) Derive an expression for the transfer function of the system. c)Cut-off frequency = 2.5kHz & Input voltage = 20mVUse the above data to determine the values of the circuit components needed to produce an output of five volts. d) Suppose a two volts input voltage is applied to the filter system, In terms of unit step function, i) what is the expression for this input? ii)Determine the output z(t) of the system. Assumption: All the circuit components in the transfer function equation have unity values.
Transfer Function and Step Response INSTRUCTIONS:1. Perform a proportional control that guarantees a settling time of 1 second, for thefirst order system given by: G(s) =g /τs + 1 Where the time constant takes the numerical value of 21 and the gain takesthe numerical value of 21
A car was ignited & a signal from the engine i.e a(z) was passed through a cascade of 2 passive RC lowpass filters to generate an output signal, b(z).a.Show a differential equation derivation to describe the systemb.Make a sketch utilizing circuit diagramc.Mention if the RC system in question above isi.Time in-variant / Time variant ii.Non linear / lineariii.Non-invertible / Invertibleiv. Non-causal / Causal v. Have no memory / Have memory sytems.d. d2b(z)/dz2 + 3(db(z)/dz) +2b(z) = 3(da(z)/dz) +2a(z)Let's assume that the d.e(differential equation) above is that which is characterised by the RC system in the main question above.Where a(z) & b(z) is the input & output of the RC system respectively.Considering an impulse of a(z)=δ(z) is applied to the system, determine the output b(z) of the system