4 Given this circuit and the pressure drops listed below:APDCV1APLINE1APLINE2APLINE3APMOTORM"APLINESAPLINE4APFILTERAPDCV2APLINE1 = 8 psiAPFILTER = 9 psiAPLINE2 = 10 psiДРмотоR - 1,278 psiAPLINE3 = 14 psiAPDCV1 = 198 psiAPLINE4 = 13 psiAPDCV2 = 135 psiAPLINES = 8 psiWhat is the pressure at the entrance of the filter when the DCV isshifted down?

Given : To find : Pressure at the entrance of the filter when DCV is shifted down

Given this circuit and the pressure drops listed below: APDCV1 APLINE1 APLINE2 APLINE3 ДРмотоR MHE "APLINES APLINE4 APFILTER APDCV2 APLINE1 = 8 psi APFILTER = 9 psi APLINE2 = 10 psi APMOTOR = 1,278 psi APLINE3 = 14 psi ДРосу1 %3 198 рsi APLINE4 = 13 psi APDCV2 = 135 psi APLINES = 8 psi What is the pressure at the entrance of the filter when the DCV is shifted down?

Given this circuit and the pressure drops listed below: APDCV1 APLINE1 APLINE2 APLINE3 ДРмотоR MHE "APLINES APLINE4 APFILTER APDCV2 APLINE1 = 8 psi APFILTER = 9 psi APLINE2 = 10 psi APMOTOR = 1,278 psi APLINE3 = 14 psi ДРосу1 %3 198 рsi APLINE4 = 13 psi APDCV2 = 135 psi APLINES = 8 psi What is the pressure at the entrance of the filter when the DCV is shifted down?

Electrical Transformers and Rotating Machines

4th Edition

ISBN:9781305494817

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter5: Autotransformers

Section: Chapter Questions

Problem 7RQ: A 480-volt three-phase load is rated at 34.5 kVA. It is to be supplied with variable three-phase...

See similar textbooks

Similar questions

4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a reciprocatingpump, turning at 200 rpm. The system useschain#100 with smaller sprocket having 21 teeth.Assuming a service factor of 1.6 using C = D2 + D1/2,determine (a) the rated horse power of the chain, (b)number of teeth of the larger sprocket, (c) the pitchlength of the chain, and (d) the number of strandsrequired. Express your answer in 3 decimal place.
A compressor that has been in service for 20 years has finally broken down beyond repair, and now must be replaced. The old 180hp machine cost $1200 and its cost index at that time was 144.5. The new machine will be 400hp. How much will the new machine cost, given that today's compressor index is 252.4 and the power-sizing exponent for compressor sizing is 0.32? A: $929 B: $2706 C: $1434 D: $2096 E: $1549
Two wattmeter’s indicate 6 kW and 5kW respectively when connected to measure the input power to a 3 phase balanced load, the reverse switch being operated on the meter indicating 5kW reading. Determine (a) the input power and (b) the load power factor.
When design for a cyclic load, if in one case, the designed reliability is 0.99, what is the approximate reliability factor which should be used according to the textbook? 1.0 0.9 0.81 0.75
Include circuit drawing and assumptions
A pneumatic system requires an average volume of 20 m³/min free air delivery.The air compressor has a rated free air delivery of 35 m³/min,a working gauge pressure of 7 bar and is controlled to switch off load when the receiver gauge pressure rises to 6 bar and back on load when the receiver gauge pressure has dropped to 5.2 bar.Determine a suitable receiver capacity if the maximum allowable number of starts per hour for the compressor is 20. Note:Assume the temperature is constant at a normal 15°C
An electric kettle is required to raise the temperature of 2 kg of water from 20ºC to 100ºC in 15 minutes. Calculate the resistance of the heating element if the kettle is to be used on a 240 volts supply. Assume the efficiency of the kettle to be 80%.a.72 ohmsc.83 ohms b.62 ohmsd.93 ohms
What is the mechanical advantage of the system shown below?
Time constant of thermocouple is 3 milliseconds. An engineer measures the temperature of water and sees that the temperature is less than the real temperature of the boiling water (100 C). How long does the engineer need to wait at least to see the 95 C? 8 milliseconds 5 milliseconds 3 milliseconds none of the given 9 milliseconds not sufficient information
Determine the controllability and observability for this system
A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
Module 4 Heating Effect of Electric CurrentHow long will it take to raise the temperature of 880 gm of water from 16ºC to boiling point ? The heater takes 2 amperes at 220 V and its efficiency is 90%.a.11.26 minc.13.08 min b.12.56 mind.14.05 min ____ 13. An electric kettle is required to raise the temperature of 2 kg of water from 20ºC to 100ºC in 15 minutes. Calculate the resistance of the heating element if the kettle is to be used on a 240 volts supply. Assume the efficiency of the kettle to be 80%.a.72 ohmsc.83 ohms b.62 ohmsd.93 ohms