GIVEN VALUE UNIT DEAD LOAD (DL) 18.50 kN/m LIVE LOAD (LL) 7.00 kN/m fy 270 N/mm^2 f'c 21 N/mm^2 LENGTH (L) 7.00 m Design a beam with one discontinuous end with the given data. Trial steel ratio is 60%. Use 20mm diameter bars. Show computations and highlight the resulting values. Lastly, draw the section of the beam.

GIVEN VALUE UNIT DEAD LOAD (DL) 18.50 kN/m LIVE LOAD (LL) 7.00 kN/m fy 270 N/mm^2 f'c 21 N/mm^2 LENGTH (L) 7.00 m Design a beam with one discontinuous end with the given data. Trial steel ratio is 60%. Use 20mm diameter bars. Show computations and highlight the resulting values. Lastly, draw the section of the beam.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

What is the design shear strength (kN) of a 4-leg 12 mmø stirrups spaced at 158 mm on centers in a 300 mm wide beam with effective depth of 530 mm? Use fy= 415 MPa for main bars and fy= 275 MPa for web reinforcement. Use f'c = 21 MPa if necessary. Express your answer in 2 decimal places.
The section shown carries a total service tension load of 508 kNwith a dead to live load ratio of 2:3. If the tension member has a length of 3 meters and A36steel, determine the following: a. The effective net area b. The LRFD design strength c. The ASD design strength d. Is the section adequate? section: C15 x 40 value of S: 63
Use ASD to determine the following. Maximum service load base on beam mechanism and portal mechanism.
A simply supported beam has a maximum shear equal to 20 KN. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual shearing stress of the beam in MPa? Blank 1 (use two decimal places)
Urgent Given the following data for a rectangular beam, b = 320 mm, d = 520 mm, f’c = 27 MPa, fy = 345 MPa.Dead Load Moment = 180 kN-m, Live Load Moment = 167 kN-m. Determine the required tension steelarea. (answer with complete solution) Final answer must be: Mu = 483.2 kN-m, FMnmax = 487.31 kN-m, c = 208.8 mm, As = 3,777 mm2
A simply supported beam has a maximum shear equal to 20 KN. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual shearing stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit).
Is ax, and bx possible get the simplier way? unit loads method is not familiar to me. Like same way how get AY and BY
Determine the numbers of rebars required for a RC beam (h=400mm, b=700mm) carrying a factored moment of 796 kPa. The concrete used has a compressive strength of 28MPa, while steel yields at 345MPa. Assume single layer of reinforcements (compression and/or tension side) and do not check for rebar spacing anymore. Other parameters: Cc = 40mm db = 20mm ds = 10mm Provide illustration if necessary and answers must be in 3 decimal places.
A simply supported rectangular beam 14 in. wide having an effective depth of 15.5 in. carries a total factored load of 10.38 kips/ft on a 25 ft clear span. It is reinforced with 6.24 in² of tensile steel, which continues uninterrupted into the supports. If f'c= 3000 psi, fyt= 40.000 psithroughout what part of the beam is web reinforcement required?. Using vertical U stirrups with fyt= 40.000 psi, design the web reinforcement for the beam and the stirrup spacing and total spacing for the beam.
Design the shear reinforcement of the beam loaded as shown using USD with fc’ = 20.7 MPa and fy = 276 MPa, fs = (fy/2)
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Design the shear reinforcement of the beam loaded as shown using USD with fc’ = 20.7 MPa and fy = 276 MPa