Plz answer correctly ty A 1800 kg car drives up an inclined of 8% fromrest at uniform acceleration to a velocity of 60kphafter traveling 75m. Its wheels are 3m. apart withits center of gravity midway of the wheels and500mm. from the ground. If all frictional force isassumed to act at the rear wheels.1) Which of the following gives the acceleration ofthe car.2) Which of the following gives the normal forceof the front wheels.3) Which of the following gives the minimumcoefficient of friction needed so that motion ispossible.

Answered: Image /qna-images/answer/2764f9c1-dbb5-4b4b-88f5-e8ab8aa6dc46.jpg

1) Which of the following gives the acceleration of the car. 2) Which of the following gives the normal force of the front wheels. 3) Which of the following gives the minimum coefficient of friction needed so that motion is possible.

1) Which of the following gives the acceleration of the car. 2) Which of the following gives the normal force of the front wheels. 3) Which of the following gives the minimum coefficient of friction needed so that motion is possible.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 3 Save Answer What will be the pressure difference between points A and B? X-135 mm & Y-50…

Q: 4-6. Determine the internal normal force, shear force, and bending moment in the beam at points C…

A: Given data in question UVL Span member length To find out Normal force, shear and Bending moment…

Q: Assignment 4. Date =18/05/2022 Q7 For the branching system as shown in figure. Calculate the…

Q: Q2: For the stresses at the point shown, find: • The maximum shearing stress. • The principal…

Q: Knowing that the coefficient of static friction between the tires and the road is 0.80 for the…

Q: Use 2015 NSCP The beam shown is a W10x77 and has continuous lateral support. The load P is a service…

A: Answer: On Equating Maximum Moment due to load on beam with and Moment strength we can calculate…

Q: Two identical 12-in. storm sewers flow full at a 2% slope into a junction box. A single large pipe…

Q: Determine the absolute maximum bending stress in the 80-mm-diameter shaft which is subjected to the…

Q: zercises: ate No. 11 > Derive the values of 6A L and 6 Ab for the following cases of loading…

A: In this question simply supported beam is given and a moment is applied in clockwise direction at…

Q: G - Q1/ Water flow through an orifice meter at an empirical equation Re = 0.35Re0- and a rate of…

A: The given data is: Empirical equation=0.35Re0-G/0.9m Re=5095.53 Q=300*10-6 m/s Cd=0.61 g=9.81m/s…

Q: Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

A: Draw the FBD showing the equivalent force and bending moment. Then using the equation of combined…

Q: A steel beam having a span “L” of 7 m is simply supported at its ends and is laterally unrestrained…

Q: Wooden planks 300mm wide by 100mm thick are used to retain soil height 3m. The planks used can be…

Q: Umax allowable compressive force is (Fe)max = 3 kN. Determine the maximum magnitude of the load P…

A: Given -

Q: If the beam carries a moving uniform load of 1.19kN/m and concentrated moving load of 114 kN as…

A: Given data in question Loads Span member length To find out Maximum moment at C Positive shear at…

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

Q: Solve for the reactions and draw the shear and moment diagram. Show complete solution.

A: Solve for the reactions and draw the shear and moment diagram.

Q: A cantilever beam of length 4.5 m supports a dead load (including self-weight) of 18 kN/m and a live…

Q: r the reactions and draw the shear and moment diagra

Q: Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

Q: Compute the location and maximum value of elastic equation curve for the beam loaded as shown. a

Q: 5. Determine the reactions at A and B for the loaded beams. Beam weight may be neglect 1m 4 m 3m 5 m…

Q: If 2340 vehicles pass a certain lane of road with an average speed of 52 kph, determine the…

A: Given, speéd of vehicle= 52 kph No of vehicle crossed in 1 hour = 2340 vehicle. To find :…

Q: Q2: A square footing (2x2 m) is constructed on a sandy soil as shown below. Find the maximum…

Q: Q7/ A differential band brake has a force of 220 N applied at the end of a lever as shown in Figure.…

Q: Solve for the reactions and draw the shear and moment diagram. Show complete solution.

A: Required : Solution for support reactions and Shear and moment diagram

Q: Please solve for the reactions and draw the shear and moment diagram.

Q: 9.6 kN-m 3.6 m 6.6 kN-m X

Q: Beam loaded and supported as shown. Determine maximum shearing and force and maximum moment using…

Q: Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. O 0.197…

Q: 2. Design the salient dimensions of a syphon well drop for the following particulars : Fall = 3.8 m…

Q: A parabolic curve has a descending grade of -0.8% and an ascending grade of +0.4% that intersect at…

Q: How did you determine the mean temperature of 304 K?

Q: Exercise No.4.3 For a given soil, show that Ysat e Yd - Ysat Ya + Yw

A: Unit Weight, g, is usually determined in the laboratory by measuring the weight and volume of a…

Q: high frictionless retaining wall supports a soil with cohesion, c'=12 kPa, friction angle=23…

Q: Answer and show complete solution. Pls don't reject A factory discharges waste water to a nearby…

Q: The rotor of an electric motor rotates at the constant rate 1 w₁ =1800 rpm. Determine the angular…

Q: Find the value of maximum shear stress in rectangular section Shear force=10.62 N Cross section…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: (a) 114 kN-m 4 m 6 m

A: step 1-

Q: For the stresses at the point shown, find: The maximum shearing stress. The principal stresses and…

Q: Enumerate the Criteria for Water Qualities. Give two methods of purifying water in remote areas.…

Q: 5@2 m = 10

Q: A 12m+ -2 m- B b -4 m- C -4 m-

Q: An old map was plotted to a scale of 40 m to 1 cm. Over the years, this map has been shrinking and a…

Q: Determine the centroidal moments of inertia and radii of gyration. Use R = 84 mm. R R/2 R/4 rad 120…

Q: F4-10. Determine the internal shear and moment in the beam as a function of x throughout the beam. 5…

A: Given -

Q: TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210…

Q: Compute the discharge flowing through the 250mm pipe. b. Compute the discharge flowing through the…

Q: An old map was plotted to a scale of 40 m to 1 cm. Over the years, this map has been shrinking and a…

Q: MULTIPLE CHOICES AND SHOW YOUR COMPLETE SOLUTION: 2. Draw the influence line diagram of the given…

A: Given :

Question

Plz answer correctly ty

A 1800 kg car drives up an inclined of 8% from
rest at uniform acceleration to a velocity of 60kph
after traveling 75m. Its wheels are 3m. apart with
its center of gravity midway of the wheels and
500mm. from the ground. If all frictional force is
assumed to act at the rear wheels.
1) Which of the following gives the acceleration of
the car.
2) Which of the following gives the normal force
of the front wheels.
3) Which of the following gives the minimum
coefficient of friction needed so that motion is
possible.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A box is released from rest at the position shown. Determine its speed (m/s) after traveling 4.9s along the 28.3ᴼ inclined surface if the coefficient of kinetic friction between the box and the surface is 0.44. Round off only on the final answer expressed in 3 decimal places.
Two blocks of the same mass are connected by a light string over a pulley of radius 0.25m and moment of inertia I. The blocks move to the right with an acceleration of 10m/s² on inclines with frictionless surfaces. Find the net torque acting on the pulley and determine its moment of inertia.
A car is being towed up on an incline with an angle of 15ᵒ with the horizontal. Find the force (parallel to the incline) needed to pull the car with an acceleration of 1.2 m/s2. The car weighs 20 kN. Neglect friction. A. 5.18 kNB. 8.36 kNC. 2.45 kN D. 7.62 kN
Two large plane surfaces are 1 in apart, and the space between them is filled with a liquid of absolute viscosity 0.0200 lbsec/ft . Assuming the velocity gradient to be a straight line, what force is required to pull a very thin plate of 4.00 ft area at a constant speed of 1.00 ft/sec if the plate is 1/3 in from one of the surfaces?
Two persons are trying to move the sofa below. If F1 = 500 N and F2 = 400 N, determine the vector expression for the resultant R of the two forces, and the magnitude of the resultant and the angle that it makes with the positive x-axis
Problem 2. Determine the velocity and acceleration of point B below. The wheel below rolls freely to the right. Compute for the required at the given position if w= 3 rad/sec and a= 5 rad/sec2, both clockwise.
Two large plane surfaces are 1 in apart, and the space between them is filled with a liquid of absolute viscosity 0.0200 lb-sec/ft2. Assuming the velocity gradient to be a straight line, what force is required to pull a very thin plate of 4.00 ft2 area at constant speed of 1.00 ft/sec if the plate is 1/3 in from one of the surfaces?
a 690N block is resting on an inclined plane and is subjected to a constant force of 875N acting parallel to the inclined plane. After the block has moved 4.69m from rest along the inclined plane, the force 600N is removed. The inclined plane has a slope of 4 vertical and 3 horizontal. Coefficient of friction is 0.23. a. Which of the following gives the distance that the block will move further along the inclined plane until it stops. b. Which of the following gives the velocity of the block when the force 875N was removed. c. Which of the following gives the velocity of the block when it returns to its initial position?
Determine the distances x and y for equilibrium if F1 = 800 N and F2 = 1000 N.
A body is thrown vertically upward with vo= 20 m/s. Find the velocity after 1.5 sec.
If a particle has initial velocity of v0 = 12 ft/s to the right, at s0 = 0, determine its position when t = 10 s, if a = 2 ft/s2 to the left.
A ball is thrown with an initial velocity of 100 ft/s upward at 60° with the horizontal. When the range is 5Oft from its original position, compute the normal acceleration of the ball and its radius of curvature.