Agui - 4550/2 =2276two plates each with thickness t - 16 mmare bolted together with 6-222 mndia.boltsfirmingalap Joint Bolt spacingare follows St-$40mm S2 - 80mm, S3=150mmeffective bolt hole dia. is 25mm A36 is used. Computethe allowable tensile StrengthPt = 16 mm&t52747₁0OO40 60 80 40+=16mmS-400$3-100S2-407 @ 4ummP

S1 = 40mm S2= 80 mmS3 = 100 mmbold dia = 25 mmt= 16mmAssume , Fu=400 MPa. Allowablestress: Tensile…

> two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts farming alap Joint Bolt spacing are follows St=40mm S2 80mm, 53= 100mm = effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm 9947, ob 00 O 40 60 80 90 +=16mm S-400 $3-100 $2.40 2

> two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts farming alap Joint Bolt spacing are follows St=40mm S2 80mm, 53= 100mm = effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm 9947, ob 00 O 40 60 80 90 +=16mm S-400 $3-100 $2.40 2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.32P

See similar textbooks

Similar questions

In the figure above, the shaft has a diameter of 50mm, and the diameter of pulleys C and D are given tobe 600 mm and 400 mm, respectively. ?1 = 1000 N, ?2 = 500 N and ?3 = 1500 N. But in addition tothe force on the pulleys, a compressive axial force of 100 kN is acting on both ends of the shaft. Theshaft is made from a brittle material with an ultimate tensile strength ??? that is half of its ultimatecompressive strength ???. The desired factor of safety is ? = 2 for the shaft.e. Determine the principal stresses corresponding to maximum bending and torsional shear stresses.Ignore transverse shear stresses due to bending.f. Use Maximum Normal Stress Theory and find the minimum required ??? and ???.g. Use Brittle Coulomb-Mohr Theory and find the minimum required ??? and ???.h. Use Modified Mohr Theory and find the minimum required ??? and ???.i. Use graphical method to check your answers in parts (a), (b) and (c).
Given a 1.3meter Wide Flange steel compression member with A=4,118mm2, Ix=87,958,354mm4 and Iy=3,574,253mm4 with Fy = 345MPa. Calculate the critical buckling stress in MPa if both ends are fixed or rigid. Express your answer in 2 decimal places.
Q - 4) In buckling experiment a steel column ( E - 210 Gpa ) was examined in pin - fixed method . It endured a load up to 1190 N. Its length is 600 mm cross sectional width is 20 mm , thickness is 4 mm. Find the critical stress and compare it with the actual stress (error %).
. A tensile load of 1120 lbs is applied to a square bar,1/2 mm on a side and having a length of 5.4 ft. Compute the stress and the axial deformation in the bar if it is made from (a) AISI C1045 hot-rolled steel, (b) SAE 8640 OQT 1000 F steel.
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
A single L8x6x1/2 (A36 steel) is used as a tension brace in a multi-story building. The 8 inch leg of the angle is attached to a gusset plate with two lines of four ¾ inch Ø bolts at a spacing of 3 inches. Determine the shear lag factor (consider Case 2 & 8) and the effective net area. Considering yielding and net section rupture, determine the design strength by LRFD and the allowable strength by ASD. (PLEASE SOLVE THIS ONE WITH THE BOLD TEXT)
In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded screw Acme with major diameter (1 in) is used with coefficient of friction (0.2135). If booth screw and nut are made from 1030 - hot rolled Carbon Steel. Determine: 1- The tightening and loosening torques. 2- Thread screw and nut shear safety factors in case of double threads are in engagement. 3.3 in 2 7.2 in 32 3 in hinge
A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.
A rod is subjed by a compressive load of 60,000 lb with shock. It is made of AISI 3140 OQT 800°F. Determine the diameter of the solid rod in inches based on the ultimate strength.
A round cross-sectional bar d= 39 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a completely reversed stresses. What is the strength of failure (in MPa) If only 10 4 cycles are needed? (Take fully corrected Se = 358 MPa, no need to use modification fcactors) (accepted answer range +/- 5 MPa)
A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di
Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ?Y=300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ?Y=300 MPa, n=2 - FOS for pin/bearing and ?Allow=300 MPa for bearing).