1500 W of power is input into a fluid with mass 15 kg and specific heat capacity of 3.2 kJ/[kg K]. What is the heating rate of this fluid assuming heat losses are negligible and there exist no changes in the pressure of the system? 1.875 K/min 0.03125 K/min 1875 K/min

1500 W of power is input into a fluid with mass 15 kg and specific heat capacity of 3.2 kJ/[kg K]. What is the heating rate of this fluid assuming heat losses are negligible and there exist no changes in the pressure of the system? 1.875 K/min 0.03125 K/min 1875 K/min

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Related questions

Q: The drive unit for a positioning table is driven by a leadscrew directly coupled to the output shaft…

A: The pitch of leadscrew, P = 0.18 in/revThe linear speed of the table, v = 35 in/min

Q: A beam subjected to a bending test has internal vertical shear force V=2000N. The cross-sectional…

Q: Determine the internal forces at point J for the structure shown, where member BD can only carry…

Q: ) The damping ratio in spring mass damper system will decrease if we: Select one: A) Adding more…

A: Damping ratio is the ratio of damping coefficient and critical damping coefficientDamping ratio, C =…

Q: Given: three forces act on a particle P. Force A has a magnitude of 55lbs and acts 30 degrees CCW…

A: Given data

Q: Determine the magnitudes and directions of forces acting at pins C and D on member BCD.

A: GivenForce acting on the CD link = 500NFind OutThe Magnitude and Direction of force acting at Pin C…

Q: Compressed air with a flowrate of 7 kg/min flows through a two-stage turbine and heat exchanger…

A: mass flow rate m= 7kg/min=7/60 kg/s=0.116 kg/sinitial pressure P1=9barinitial temperature…

Q: Maksimum 900 K ve minimum 283 K sıcaklık aralığında hava standardına göre çalışan ideal Brayton…

A: The compressor inlet temperature, T1 = 100 kPaThe maximum temperature, Tmax = 900 KThe minimum…

Q: A thermal evaporator is used to deposit aluminum. The aluminum charge is maintained at a uniform…

Q: The manhole cover of an ammonia storage tank is to be held by 25 stud bolts. If the pressure inside…

A: The number of bolts, n=25The pressure inside the tank, The manhole diameter, D= 508 mm=50.8 cmTo…

Q: Two aluminum plates, each having a width of b = 4.9 in. and a thickness of f = 0.650 in., are welded…

Q: Match the term to the correct definition. When a load carrying member is subject to an alternating…

A: Definition of Load and Loading:Load refers to an external force or combination of forces that act on…

Q: A B 50kg Rope ABCD is placed over two pipes that do not rotate. Knowing that the coefficient of…

A: The mass of the block A is 50 KgHence the tension in the string ABAnd coefficient of friction

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: 1. A control rod AB is fixed with a pin connection at B. The rod is 26 in long and is at an angle of…

Q: Two couples act on a rectangle with a base of 7 m and a height of 4 m. Determine the magnitude and…

Q: Question 3 (a) A system is critically damped. Derive an expression for the time at which the…

A: Q3(a)The natural frequency of the system, wn = 2.5 rad/sThe initial displacement, Xo = 0 mmThe…

Q: QUESTION 3 Which is true about the velocity at point 1 (4) h3-1 (3) (1) O V1 > V2 O V1 < V2 O V1 =…

Q: Two pounds mass of water in a piston-cylinder assembly, initially a saturated liquid at 35 lb/in²,…

A: m=2lbP1=P2=35lbf/in2state 1P1 =35lbf/in2 and saturated liquid T=259.30 F= 718.97 Rv1 = 0.01708…

Q: a) Perize expression-for-the-closed-loop-system-undamped natural frequency and damping ratio... Lin

A: First, comprehend the parts of the closed-loop system in order to get the equations for the undamped…

Q: A plate is lapped over and welded to a gusset plate as shown in the figure Calculate the Polar…

Q: A double-threaded worm with a lead angle of 20 degrees and axial pitch of 12.7 mm/tooth drives a…

Q: Write an article describing possible data and big data analytics to the Mechanical Engineering…

A: In the digital era, data and big data analytics have transformed various industries, and mechanical…

Q: In order to make an adjustment, a group of engineering students remove leg D from a laboratory…

Q: (Pr. 1) In an isotropic medium, Poisson's ratio v relates Young's modulus to either the shear…

A: Hi, As per the guidelines, we can solve only first question for you since the exact one is nor…

Q: From the consideration of the stress element, the shear stresses at x-plane and y-plane must be: of…

A: There is a stress element which is in the equilibrium condition. so all the net external forces and…

Q: Draw the primary and secondary auxiliary views. FRP PRP

A: According to the given data.There is two view of the object.We need to draw the auxiliary view of…

Q: The worktable of a numerical control machine tool is driven by a closed-loop positioning system…

A: Given data as below:pitch p = 0.25 in/revthe distance at which table moved x = 7.5 infeed rate fr =…

Q: Consider the channel shown in (Figure 1). Suppose that a = 320, mm b = 260 mm, c = 40 mm. Figure 1…

A: a = 320, mm b = 260 mm, c = 40 mm.To Find-The location y of the centroid of the channel's…

Q: Indoor air dry bulb temperature and relative humidity are 23 C and 45%, respectively. Determine a)…

A: According to our guidelines , we are supposed to answer 1st three sub parts . Please re-post other…

Q: A kid excitedly swings his foam cut-out hammer. If point P acts like a pin and the hammer rotates…

A: Given data as below:To determine:Moment of Inertia of Hammer

Q: Endurance Limit calculations are suited for types of loading Random Static Impact Repeated and…

A: Endurance limit is the maximum value of the fully reversed bending stress which a material can…

Q: II. Solve using the modeling method in the states space, output It is displacement 3 and VO…

A: Given:To find:State space

Q: Differentiate between a saturated vapour and a superheated vapour?

A: Vapour: A phase of a fluid at a temperature where the same substance can exist in both solid and…

Q: A 600 N volleyball player lands from a spike attempt and immediately jumps up to try for a block.…

A: Given:To find:Work done and Average vertical GRF

Q: Hot air, initially at 340 °F and 150 psi, is released to the atmosphere (14.7 psi) through an…

Q: Can copper alloy be hardened through heat treatment? justify. If not, suggest suitable processes…

A: Heat treatment is a process by which a metal can be heated below the melting point and then cool to…

Q: Consider the beam shown in the figure. The bending moment in the middle of span AB is most closely…

A: According to the given dataWe need to findThe moment in the middle of the beam

Q: Given the two views of a solid and an auxiliary reference plane, draw the auxiliary view and…

A: We have Draw Auxiliary view of the given figures.

Q: A metal is heated up to a temperature of 500 degrees Celsius. It is then exposed to a temperature of…

A: The time required to reach .Given:The initial temperature of the metal is .The surrounding's…

Q: Q2//A/ Find the unit step response for a system whose transfer function is: G(S) = 10 (S + 2) (S +…

Q: Task Ib 13 i. 12 P 270 N 70° [All forces: FPQ, FPR, FRS S 55° Figure Ib shows a crate with a weight…

A: shows a crate with a weight of 270 N supported by the vertical pole RS. Based on the figure, To…

Q: If r = (4, -2, 2) and F = (4, 8, 4), what is r x F?

Q: Find the transfer function for the system illustrated in Figure P2.59. Express the transfer function…

A: m = 10 KgK1 = 400 N/mC = 14.14 N-s /mK2 = 100 N/m

Q: Can the statue be dragged without tipping? O Yes No Frip xN If the movers can apply the force…

Q: NEED HELP WITH D THRUGH G

A: From the free body diagram, evaluate angle .Substitute .

Q: determine the angular velocity of the rod when 0 = 0°.

Q: as a beam, is a vertical support by two fillet welds as the figure. Find the safe bending force Fif…

A: h=5mmC=150mmb=d=50mmallowable shear stress=140MPa

Q: c. Determine critical load and critical stress for the column/axial member. Justify selection of…

A: The column is fixed at both ends.External axial load appliedYoungs modulusDiameter of the…

Q: Determine the new angular velocity.

A: Moment of inertia about man's center of mass Moment of inertia about woman's center of mass Mass of…

Question

1500 W of power is input into a fluid with mass 15 kg and specific heat capacity of 3.2 kJ/[kg K]. What is the heating rate of this fluid assuming heat losses are negligible and
there exist no changes in the pressure of the system?
1.875 K/min
0.03125 K/min
1875 K/min
45 K/min

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: We will write the given and required

VIEW

Step 2: We will calculate heat rate by applying the formula for power in terms of heat rate.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Energy consumption in a country from 2001 to 2011 increased from 1041.3 million to 1526.1 million BOE (barrels of oil equivalent). If the high calorific value (HHV) of the oil is 141,000 kJ/gallon what is the increase in energy consumption over 10 years in Joule units. What is the rate of energy consumption per year? 2. Based on data on the rate of energy consumption per year from question no. 1, if the growth rate energy 2.5% per year, calculate the doubling time (td) and what is the approximate rate of energy growth in 2021.
Please show the complete solution. (Example: Conversion of Units) How much heat in kJ must be transferred to 20 kg of air to increase the temperature from 20 Degree Celsius to 280 Degree Celsius if the pressure is maintained constant?
Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid
the specific heat (cp or cv) can also be understood as a "capacity or ability of a given material to store "heat". In this way, we can say that: 1- the greater the specific heat, the greater the amount of "heat" needed to cause an increase or decrease in temperature per unit mass of the material.2- the higher the specific heat, the lower the amount of "heat" needed to cause an increase or decrease in temperature per unit mass of the material3- the lower the specific heat, the greater the amount of "heat" needed to cause an increase or decrease in temperature per unit mass of the material4- the lower the specific heat, the amount of "heat" needed to cause an increase or decrease in temperature per unit mass of the material does not change5-the higher the specific heat, the amount of "heat" needed to cause an increase or decrease in temperature per unit mass of the material does not change choose only one of the above alternatives as correct
The Ideal gas law shows the relationship between some common properties of ideal gases and is written as PV = nRT. P = pressure, V = volume, n = number of moles of ideal Gas, R = General gas constant = 8.314 kJ/(kmol.K) and T = absolute temperature. 5 mol ideal gas at 22°C is placed in a cube with edge lengths of 0.750 meters. Calculate the pressure of the Ideal gas as [Pa].
THERMODYNAMICS: Mollier Diagram: Steam Table Using the Steam Table below, find Δhf and Δhg in BTU/lbm and Δsf and Δsg in kJ/kgm-K and for the following parameters: P1 = 9.5 kgf/cm2 P2 = 15 kgf/cm2 With step by step explanation pls NOTE: This table uses SI unit as stated below: Pressure: MPa Temperature: °C Internal Energy and Enthalpy: kJ/kgm Entropy: kJ/kgm-K
Fluid mechanics A manometer, utilizing a pitot probe, measures 10 mm of mercury. If the velocity is desired in a pipe transporting water to which the manometer is attached, what additional information in the following list is needed? I. The temperature of the water II. The pressure in the pipe III. The density of the mercury IV. The diameter of the pipe A. I and II B.II and III C.III and IV D.II and IV
#01: Explain the following terms in your own words. a) Aerodynamics. b) Mach Number. c) Sub-Sonic. d) Angle of Attack. e) Thrust. f) Chord Line. g) Drag Coefficient. h) Pitch Moment. i) Wind Tunnel. j) Skin Drag.
We have superheated steam at a pressure of 0.05 bar and temperature of 366.62 oC. What is the specific volume in units of m3/kg? Use the steam tables and report your answer to three decimal places. Note that in the steam tables, the specific volume is reported in units of m3/kg.
Four hundred cubic centimeters of a gas at 740 mm Hg absolute and 18℃ undergoes a process until the pressure becomes 760 mm Hg absolute and the temperature 0℃. What is the final volume of the gas in cc?
The heat transfer coefficient is a nondimensional parameter which is a function of viscosity ? , specific heat cp (kJ/kg·K), and thermal conductivity k (W/m·K). This nondimensional parameter is expressed as (a) cp/? k (b) k/? cp (c) ? /cpk (d ) ? cp/k (e) cpk/?
A certain gas weighs 7 KN/m3 at a certain temperature and pressure. What are the values of its density, specific volume, and specific gravity relative to air weighing 12 N/m3?