hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di

hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.1P: A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness...

See similar textbooks

Related questions

Q: The load on square section bar consists of a transverse shear force of 12 kN together with an axial…

A: Given: P=20 kNFt=12 kNσy=260 MPaf=1.8ν=0.28

Q: Q2// Determine the diameter of a circular rod made of ductile material with a fatigue strength…

A: Given, Fatigue strength, se'=270 MPa=270 N/mm2 Tensile yield strength, syt=370 MPa=370 N/mm2 The…

Q: Select the lightest W shape that will act as a column of 7 m long with both end hinged and support…

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7 m long,…

A: Given data W12 x 79 Grade 60 (Fy= 415Mpa) Length Lx=6.7m Ly=6.7/2 = 3.35m The top and Bottom both…

Q: A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central…

Q: Determine the minimum diameter value [cm] for a pin operating under double shear stress and having a…

A: The factor of safety for the shearing is, f=5 The shear force acting on the pin is, P=85 kN The…

Q: A cylindrical rod of copper (E = 110 GPa, 16 ´106 psi) having a yield strength of 240 MPa (35,000…

Q: Example 7.2 Two plates are fastened by means of two bolts as shown in Fig. 7.14. The bolts are made…

A: Given P-5kN S-400 N/mm² (fs) = 5 kN To find :- Size of bolts Step 1 Permissible shear stress Sxy =…

Q: What is the minimum load needed for a bar of chocolate to break if it has a thickness of 10mm, a…

A: Given, Thickness of bar,t=10mmLength of the bar,L=0.095mwidth of the bar,w=0.05mFlexural stress of…

Q: To use deformation compatibility equations to calculate loads and deflections for statically…

A: Free Body diagram: Taking moment about F2 ∑MF2 = 0-F1(L1+L2)-P(L2) = 0F1 =…

Q: A steel bar with a maximum usage strength of 400MPa. 30kN axial tensile loads to be applied If so,…

A: Given Mximum usage strength = 400MPa Working strength = Maximum usage strength / Factor of safety…

Q: The plate shown is made of an AISI 1050 CD steel and is subjected to M, = ±12,000 Ib.in. If a factor…

A: From the given figure, z-axis is the neutral axis. Calculate the maximum value of the distance from…

Q: A short column is composed of two steel E-31.000 k v 0.30) segments, each with a length of 4.5 in…

A: Find , Deflection in the steel column.

Q: A solid circular rod of diameter d undergoes a bending moment M= 1500 lbf-in inducing a stress o=…

Q: The bars, shown in sketches (a) and (b), are made from cold-drawn, AISI 1050 QT at 425 °C medium…

Q: 13. An airplane’s landing gear must be capable of supporting ⅓ of its weight at 200000 kg. To induce…

A: Given Data The weigth of the aircraft is:W=200000 kg The yield strenght is:σyt=860 MPa The tensile…

Q: ermine the parameters for each question below, assume E = 200 GPa. i) Critical load for the square…

A: Given:Modulus of elasticity, E=200 GPa

Q: The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6…

Q: The notched bar shown in the following figure is subjected to an axial load P that varies between…

A: The ultimate aim of the design is to prepare a drawing or chart in such a way that the resulting…

Q: A long tensile member is constructed by connecting two plates as shown. Each plate is 2 in x 9 in,…

Q: composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy…

Q: etermine the diameter of a brittle member in inches if the tensile design load is 15,671 lb.…

A: Given:Tensile load, P=15,671 lbUltimate strength, Sut=60,000 psiN=5

Q: Determine the diameter of a circular rod made of ductile material with a fatigue strength (complete…

Q: Determine the ratio of buckling strengths of two columns of circular cross-section, one hollow and…

A: Let's assume the diameter of the solid column is Ds. and the external diameter of the hollow column…

Q: A steel plate subjected to a force of 5 kN and fixed to a channel by means of three identical bolts…

A: Given DataP=5 kNSyt = 380 mPaFos =3

Q: A short column is composed of two steel (E-31.000 k v=0.30) segments, each with a length of 4.5 in…

A: The shortening of the segments: ( 3.76408 × 10-4 ) inch.

Q: A circular bar of 500 mm length is supported freely at its two ends. It is acted upon by a central…

A: Given data - l = 500 mm, W min =20 KN = 20 x 103 N 6 y…

Q: While the flag is waving on top of its pole during a windy day, unfortunately the pole bends…

A: Since flag is waving on top of its pole during a windy day, flag is subjected to wind force. Due to…

Q: Determine the size of a piston rod subjected to a total load of having cyclic fluctuations from 15…

Q: A pipe with a wall thickness of 6 mm is designed to operate at the hoop stress of 600 MPa and the…

A: Given Data⇒ Hoop Stress σh=600 MPa Axial Stress σa=300 MPa Damage tolerance safety factor SFk=1…

Q: Which of the following is the design stress for a piston rod where the axial load is completely…

A: Given data: ksur=0.9FOS=2ka=0.85σe=250 MPa Need to determine the design stress.

Q: A circular bar of "500" mm length is supported freely at its two ends. It is acted upon by a central…

Q: (6) A wall bracket is loaded so that the two top bolts that fastened it to the wall are subjected to…

A: Given: Let us consider the given, Sy=48 ksiF=1420 lb To find: if the bolts are well-tightened,…

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1and R2. The…

Q: A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a…

Q: modulus of elasticity equal to 200x103 MPa and coefficient of thermal expansion equal to…

Q: 2) The pillow block shown in Figure 2 is attached to the fixed plate by using two M20x1.5 ISO class…

A: Introduction: A factor of safety factor is an engineering phrase that describes how much stronger a…

Q: hollow short compression member, of normalized cast steel where Su = 65 ksi, is to support a load of…

A: Given Data Su = 65 ksi P=1500 Kips F=8 Do =2Di

Q: The steel rod in Fig. is to be used to support an axial load of 18 kip. If Est = 29(103 ) ksi and…

A: Given data: The applied load, P = 18 kip. The modulus of elasticity, E = 29 × 103 ksi. The yield…

Q: The top lid of a nuclear reactor is being held by clamping screws which are made of AISI 4340 steel…

A: We have to determine factors of safety guarding against yielding and the factor of safety guarding…

Q: A thin-walled cylindrical pressure vessel made from a grade of aluminium has an internal diameter d…

Q: A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is…

Q: 2. A 45-cm long rod of 1020 grade steel will be used as a frame support. It will be subjected to a…

Q: Material J is suggested to be used as a rod with the applied stress up to 150 MPa. Material J has a…

A: Given data: ◆ The yield strength of material: σyield = 340 MPa ◆ The factor of safety: FOS = 2 ◆ The…

Q: Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained?

Q: Factor of Safety =3 Material for Member AB is ASTM A36 Steel bb is cross-section of member AB.…

A: Factor of safety=3 AB=2m BC=0.5m

Question

A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
A bar having a length of 30 in. is used to support an axial compressive loadof 12 kip, Fig. It is pin supported at its ends and made of a 2014-T6 aluminum alloy. Determine the dimensions of its cross-sectional area if its width is to be twice its thickness.
22. Series of steel wires support a large tower. It is estimated that the load on each wire will be 2500 lbf. Determine the minimum required wire diameter (in inches). Assuming factor of safety of 2 and a yield strength of 1030MPa. Round of to nearest tenths.
Which of the following is the design stress for a piston rod where the axial load is completely reversed if the surface of the rod is ground and the surface finish factor is 0.9? Assume no stress concentration. Use a factor of safety of 2 and an endurance limit of 250 MPa. The load factor for completely reversed axial load is 0.85.
Determine the diameter of a brittle member in inches if the tensile design load is 15,671 lb. assuming a factor of safety of 5 based on an ultimate strength of 60,000 psi.
Determine the critical load for a pinned-end column made of a circular bar of AISI1020 hot-rolled steel. The diameter of the bar is 20 mm, and its length is 800 mm.
10.20: Design a 3-m- long rod subjected to a tensile load of 67.5 kN. Using a factor of safety of 2.5 based on the yield stress, calculate the required rod diameter if it is to be made of (a) steel with a yield stress of 310 MPa. (b) aluminum alloy with a yield stress of 240 MPa.
Select the lightest W shape that will act as a column of 7 m long with both end hinged and support an axial load of12KN with the safety factor of 2.2, assume the proportional limit for steel is 200 Mpa and E=208 Gpa
A M20 × C4 bolt of mild steel is having yield stress of 320 MPa and factor of safety 3. The safe static tensile load in kN will be
An industrial machine requires a solid, round piston connecting rod 200 mm long, between pin ends that is subjected to a maximum compression force of 80,000 N. Using a factor of safety of 2.5, what diameter is required if aluminum is used with properties Sy = 496 MPa and E = 71 GPa.
A circular-cross-section bar with a diameter of 50mm and a length of 1.25 m is axially loaded. The baris made of medium-carbon steel. Both ends are pinned.Determine(a) Whether the Johnson or the Euler formula shouldbe used.(b) The critical load.
(a) Explain FIVE (5) factors that may influence the optimum column design under an axial compressive load. (b) A 3.6 m long pin-ended column is formed from an A-36 steel circular hollow section with an outer diameter of 75 mm. Determine the minimum thickness, t (to the nearest integer in mm) of the circular hollow section so that the column can safely support the load of 200 kN without buckling. If the outer diameter of the steel circular hollow section is reduced to 62 mm and the ends are pinned-fixed supported, analyse whether the column with the same applied load and the sectional thickness computed above will cause a buckling failure.