Group D: Connect a Parallel dc circuit consists of: R1- 5.6 KO R2= 6.8 KO R3= 7.5 KO E- 10 v 1. Determine the theoretical and measured voltage through the circuit. 2. Apply Ohm's law to determine the expected current through R1, R2, and R3. 3. According to the results, How did Kirchhoff's Current Law satisfy?

Group D: Connect a Parallel dc circuit consists of: R1- 5.6 KO R2= 6.8 KO R3= 7.5 KO E- 10 v 1. Determine the theoretical and measured voltage through the circuit. 2. Apply Ohm's law to determine the expected current through R1, R2, and R3. 3. According to the results, How did Kirchhoff's Current Law satisfy?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Topic: Direct Current Circuit which contains Open and Short Circuit, Series and Parallel Circuit, Current Divider Principle, Voltage Divider Prinicple, and Delta-Wyne Connection. Determine the value of VT and I. Note: DRAW THE DIAGRAM
Using Kirchhoff's Rules, compute the current (mA) and voltage (V) values of the circuit if R1=2kohm and R2=7kohm.
Answer the following questions related to a series/parallel combinational circuit configured as follows: R1 is in series with the source and also in series with the parallel combination of R2 and R3. The circuit’s voltage is +24VDC, R1= 4.5kΩ, R2=30kΩ, and R3=10kΩ. What is the Thevenin’s voltage (ETH) for the circuit described above if a load resistor of 20kΩ is placed in parallel with R2 and R3?
In the circuit below, the voltage sourse Vin = 12(V), and node D is grounded. Given R1 = 12 (Ω), R2 = 16 (Ω), R3 = 16 (Ω), and R4 = 16 (Ω). Find the voltage dropped cross R2, VA-VB, in volts.
Mesh current methods can greatly reduce the calculations as compared to Kirchhoff’s voltage and current laws in circuits with multiple branches. Refer to the textbook reading and the lecture for this week to answer the following post. Describe, step-by-step, the steps required to calculate all currents and voltage drops in a DC network using the Mesh Current Method.
For the circuit shown in the figure above, what is the equivalent resistance seen from the a-b terminals? Assume R1 = 181, R2 = 353, and R3 = 584.
Answer the following questions related to a series/parallel combinational circuit configured as follows: R1 is in series with the source and also in series with the parallel combination of R2 and R3. The circuit’s voltage is +24VDC, R1= 4.5kΩ, R2=30kΩ, and R3=10kΩ. What is the Thevenin’s resistance (RTH) for the circuit described above if a load resistance of 20kΩ is placed in parallel with R2 and R3?
3. a. by applying Kirchhoff's junction rule to two junctions find the current I5. b. by applying Kirchhoff's loop rule, find the resistances R2. c. by applying Kirchhoff's loop rule, find the reistences R3.
Answer the following questions related to a series/parallel combinational circuit configured as follows: R1 and R2 are in series with the source and these two resistors (R1 and R2) are in parallel with R3. The circuit’s voltage is +18VDC, R1= 1.5kΩ, R2=4.5KΩ, and R3=30kΩ. The total current drawn by the circuit described above is __________. Use correct engineering notation and unit measure! The total resistance of the circuit described above is _________. Use correct engineering notation and unit measure! The current drawn by R2 in the circuit describe above is _________. Use correct engineering notation and unit measure! The voltage drop across R1 in the circuit described above is __________. Use correct engineering notation and unit measure! The power dissipated by R3 in the circuit described above is __________. Use correct engineering notation and unit measure!
For the circuit shown in Figure 2.1, write down the nodal equations for the circuit and solve for V2 and V3if both VS1 and VS2 are 15V. Show all the calculations involved
After transforming R2, R3, and R5 from wye connection to delta connection, what are the values of the resistances (in ohms) of the resulting delta connection? List them in any order below
Circuits 1 and 2 are connected at their terminals B and D. We are given the following values: R1 = 8 Ω, R2 = 5 Ω, R3 = 4 Ω, V1 = 10 V, I1 = 3.5 A, and I2 = 3 A. Using nodal analysis, we can derive nodal equations for node C and supernode V1 in terms of the nodal voltages VA, VB and VC. From the circuit, we can get the relationship V1=VA−VB and can be re-written to the form: a0VA + b0VB + c0VC= d0 --> (−1)VA +(1)VB + (0)VC = 10 V1 is also a supernode that combines nodes A and B. We can derive a nodal equation and rewrite it to the similar form: a1VA + b1VB+ c1VC = d1. Similarly, for node C, nodal equation can be derived and written into similar form: a2VA+ b2VB + c2VC = d2 Determine value of a1, b1, c1, and d1 as well as value of a2, b2, c2, and d2, respectively.