H.W: Design a knuckle joint for a tie rod of a circular section to sustain a maximum pull of 70 kN. The ultimate strength of the material of the rod against tearing is 420 MPa. The ultimate tensile and shearing strength of the pin material are 510 MPa and 396 MPa respectively. Determine the tie rod section and pin section. Take factor of safety = 6.

H.W: Design a knuckle joint for a tie rod of a circular section to sustain a maximum pull of 70 kN. The ultimate strength of the material of the rod against tearing is 420 MPa. The ultimate tensile and shearing strength of the pin material are 510 MPa and 396 MPa respectively. Determine the tie rod section and pin section. Take factor of safety = 6.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the plates – t, mm is 12 Width of the plates – b, mm is 150 Load – P, kN is 20 Note. Choose a suitable material, determine its tearing stress. Take permissible shearing stress - teta=0.7sigmat ; Permissible crushing stress - sigmac=1.5sigmat ;
In a bolted joint two members are connected with an axial tightening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque required for achieving the tightening force is
Design a turnbuckle subjected to a load of 50 kN with permissiblestresses are in 166.67 Mpa in tension , 83.33MPa in shear and 166.67 MPa incrushing. (Please provide a handwritten solution, thank you)
MACHINE DESIGN TOPIC A short compression member with Do = 2Di is tosupport a dead load of 25 tons. The material isto be 4130 steel, WQT 1100 F. Calculate theoutside and inside diameters in terms of incheson the basis of (a) yield strength, (b) ultimatestrength.*For 4130 steel, WQT 1100 FSu = 127 ksiSy = 114 ksi*Use the following Safety FactorsNu = 4Ny = 2
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
Reduction of a simple distributed loading
What is the shear stress, fv, for the glue of the lap of the connection with P= 15,000 lb? What is the axial stress due to tension, ft, on the thinner of the two plates?
A mild steel cover plate is to be designed for an inspection hole in the shell of a pressure vessel. The hole is 120 mm in diameter and the pressure inside the vessel is 6 N/mm2. Design the cover plate along with the bolts. Assume allowable tensile stress for mild steel as 60 MPa and for bolt material as 40 MPa
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
Question No.15: Design muff coupling to connect two steel shafts transmitting 40 kW at 350 rpm. The material for shafts and key is plain carbon steel for which allowable shear and crushing stresses are 40 MPa and 80 MPa respectively. The material for muff is cast iron for which allowable shear stress is 15 Mpa
Problem 18.20, please show all work? Section 18.7 Axially Loaded Steel Machine PartsFor Problems 18.18 through 18.21, use the Euler–Johnson formulas, Equations (18.9) and ( 18.10), and a modulus of elasticity of 30,000,000 psi. 18.18 Calculate the allowable axial compressive load for a bar of rectangular cross section that measures 1 in. by 2 in. and is 20 in. long. The member is made of AISI 1040 hot-rolled steel. Use a factor of safety of 3.5 and assume the member is pin-connected. 18.19 Compute the required diameter of a piston rod of AISI 1040 hot-rolled steel with a length of 20 in. The rod is subjected to an axial compressive load of 6000 lb. Use a factor of safety of 2.5. Assume that the rod is pin-connected. 18.20 Compute the required diameter of an air cylinder piston rod of AISI 1040 hot-rolled steel. The rod has a length of 54 in. and is subjected to an axial compressive load of 1900 lb. Assume pinned ends. Use a factor of safety of 3.5. 18.21 Compute the required…
Design a single riveted lap joint to connect two mild steel plates, 14.5 mm thick, the joint being designed for maximum efficiency. The allowable stresses are σt = 55 N/mm2 , = 32.5 N/mm2 and σc = 63.5 N/mm2 . Also calculate the minimum force per pitch which will rupture the joint