H.W.12// A vertical conduit is carrying oil (SG 0.95). A differential mercury manometer is tapped into the conduit at points A and B. Determine the difference in pressure between A and B when h = 3 in. What is the difference in the piezometric pressure between A and B? SGm = 13.6 Menury

H.W.12// A vertical conduit is carrying oil (SG 0.95). A differential mercury manometer is tapped into the conduit at points A and B. Determine the difference in pressure between A and B when h = 3 in. What is the difference in the piezometric pressure between A and B? SGm = 13.6 Menury

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: PROBLEM 3: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two…

Q: If H = 4 m, D = 10 m, h = 0.4 m, k = %3D 0.0001 cm/s and y = 0.2 m, the porewater pressure at C is…

A: Given data in question Coefficient of permeability Upstream head Downstream head To find out Pore…

Q: In Fig. P2.43 pipe A contains gasoline 2.43 (SG = 0.7), pipe B contains oil (SG = 0.9), and the…

Q: Based on the provided differential-type manometer, calculate the difference in the pressure between…

A: To find :- the pressure difference between points A & B.

Q: H.W.10// Is the gauge pressure at the center of the pipe (a) negative, (b) zero, or (c) positive?…

A: Given data: h1=6 in. h2=12 in. h3=30 in. S.G1 =1 S.G2=2

Q: A pitot tube having a coefficient of velocity=0.978 is used to measure the velocity of water at the…

A: For Pitot tube Velocity is v=Cv2gh

Q: 4. An inclined tube manometer has the area of the reservoir as 277 mm² and diameter of the inclined…

A: Question is based on manometer tube . Area of reservoir , diameter of inclined tube, Specific…

Q: A sphere 900mm-diameter floats half submerged in a tank of oil (sg=0.90) What is the total vertical…

Q: Q2) What is the pressure at point (B)inside the pipe shown in figure below if the water jet velocity…

A: Given data in question Diameter Velocity Elevation To find out Pressure at B

Q: A vertical 150-mm-diameter pipe leaves a water tank that has a surface elevation of 12m. Between the…

A: Velocity of flow at 0 elevation=Q/A Area=A=πd24 d=150/1000=0.15 m A=3.14×0.152/4=0.0177 m2…

Q: P.3.5 Three pipes A, B. and C at the same level connected by a multiple differential manometer shows…

A: Let Density of water be ρw = 1000 kg/m3 Density of mercury = ρHg = 13500 kg/m3 Differential…

Q: identify the type of manometer and then solve. Determine the difference in 02 pressure between A and…

A: The given data is: h1=0.2 m h=0.15 m h2=0.3 m SGoil=0.862

Q: A sump pump (used to drain water from the basement of houses built below the water table) is…

Q: M oil SG 0.8 30cm 50cm 20cm Mercury N oil SG 0.8

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

Q: Based on the provided differential-type manometer, calculate the difference in the pressure between…

Q: Air I. Elevation= zB Oil (SG = 0.85) Elevation zA Figure 7 トー

A: Elevation of point A is (Za) = 10 m Elevation of point B is (Zb) = 11 m Elevation between point A…

Q: Determine the capillary rise (in mm.) of a liquid (SG = 3.47) placed on a capillary tube with…

A: Given data : Diameter (d)=1.77 mmSurface tension (σ)=0.675 N/mContact angle (θ)=8∘Specific gravity…

Q: Use SGmercury (Hg) = 13.6. a.) If the manometer reads "Rm" 60 mm, find the gage pressure (kPa) at B.…

A: Take the pressure equation from the one end to other…

Q: Air (p = 1.2 kg/m3) flows through an orifice plate set in a pipe of 400 mm diameter. A water…

A: Given Data: The density of air is ρ=1.2 kg/m3 The diameter of pipe is d1=400 mm. The area of the…

Q: Example 2.2 cury manometer (sp. gr. = 13.6) is co measure the pressure differenc sels A and B, as…

A: Density of manometer at A and B are not known Consider ρA=ρB=1000 kg/m3 Density of mercury…

Q: P.3.5 Three pipes A. B. and C at the same level connected by a multiple differential manometer shows…

A: Some standard units for pressure 1 bar= 105 Pa

Q: The pressure gauges G, and G, installed on the system show pressure of PG1 = 5.00 bar and PG2 = 1.00…

Q: Consider a vertical pipe of diameter 3.136 mm. Through this pipe kerosene (density 963 kg/m3 and…

A: Given data in question Pressure at below point Diameter Discharge Density of oil To find out…

Q: The inverted U-tube manometer contains oil (0.90) and water as shown. Oil h 0.2 m 0.3 m Water

Q: A differential manometer is used to measure the pressure ditlerence between two points in a pipe…

A: Given data in question Manometric liquid Height difference Value of h To find out Pressure…

Q: Based on the provided differential-type manometer, calculate the difference in the pressure between…

Q: Water is flowing in a pipeline, the pressure in the inlet pipe is 20 kPa there is a gradual decrease…

Q: Compute for the unknown pressure at A. = 90 cm; h2 = 150 cm; h3 = h4 =65 cm). Encode your answer…

Q: EX: A piezometer and a Pitot tube are tapped into a horizontal water pipe to measure static and…

A: Consider the diagram of the system shown below.

Q: 1. Hydrostatic force on a curved surface Consider the container with the half-sphere dome, filled…

A: radius of sphere R = 1 m Height = 10 m

Q: Problem 3 The pressures Pa and Pg in the differential manometer gage are 154.415kPag and 150 kPag…

Q: es at entrance and exit of conical daft tube are y the entrance of draft tube. Assume friction lo…

Q: A 84-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure. If…

A: Bernoulli's theorem assumptions: The flow is incompressible. The flow is steady( Pressure, density,…

Q: A 200 mm 150m GOO min

Q: The Pitot tube and a wall piezometer tube are connected to a water-mercury manometer which registers…

A: Asked: To determine the pressure head difference (meters of water) and the velocity approaching the…

Q: H.W1: Determine the pressure difference between points A and B in Fig below? 3 Note: pe = 1. 2kg/m',…

A: Density of all the fluids are given in the question itself. We are required to find the pressure…

Q: El 2 m Liquid A (s.g = 0.72) Figure 1 %3D El 0.3 m Liquid B (s.g 2.36) El %3D .0m

Q: An orifice meter that has an orifice cross-section of 0.00785 m² is placed in a tube of cross…

A: Given: Orifice cross section, A1 = 0.00785 m2 Tube cross section, A2 = 0.0314 m2 Upstream pressure,…

Q: The figure shows a cylinder of 4 m dlameter in equilibrium. Calculate the vertical component of…

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A: Given hw=45mm=0.045m hHg=160mm=0.16m

Q: An inverted differential manometer is connected to two pipes A and B which convey water. The fluid…

A: I have followed usual notations of inverted manometer

Q: 7. If the pressure in a gas tank is 2.50 atmospher find the pressure in kPa and the pressure head…

A: Given : A gas tank consist pressure of 2.5 atmosphere. find : pressure in KPa and pressure head in…

Q: Q1/ The diagram below shows an inclined tube manometer connecting two pipes. Determine the change in…

A: hw = Height of water = 18 in.hm = Height of mercury = 6 in.ho = Height of oil = 12 in.ρw = Density…

Q: Convert the 115/85 systolic/diastolic pressures given in millimeters of Hg to Pa .

A: To convert mmHg to Pa

Q: Determine the pressure in a vessel of mercury (sp.gr. = 13.6) at a point 300 mm below the surface in…

A: Given Data: Specific Gravity = 13.6 Height of mercury = 300mm = 0.3m

Q: 2.4.7. An open manometer, shown in Figure P2.4.7, is installed to measure pressure in a pipeline…

A: Given data Oil specific gravity Manometric fluid Height of Manometric column

Q: Q1: the pressure at point A is 172 pa. All fluids are at 20°C. The air pressure in the closed…

A: to find pressure at point B

Q: For the fo type of manometer an Determine the difference in pressure between A and B in kPa if h =…

A: Given Data: h=0.15 and SG of oil =0.662 To Calculate: Pressure difference in pipe using…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

H.W.12// A vertical conduit is carrying oil (SG = 0.95). A differential mercury
manometer is tapped into the conduit at points A and B. Determine the difference in
pressure between A and B when h = 3 in. What is the difference in the piezometric
pressure between A and B?
SGm = 13.6
18 in
Oil
A=3 in
Merury

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q3) A differential manometer is connected at two points A and B of two pipes. The pressure at A and B are 1 bar and 2 bar respectively. Find the difference in mercury level in the diffrential manometer. (12
Calculate the pressure difference between points A and 13 in the differential manometer shoon."
Q/ Compute the prassure at point B in the Pipe of water if heigt h is: 0.3 m. and the difference heigh mercury In manometer is z = 0.4m
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014 *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
Based on the provided differential-type manometer, calculate the difference in the pressure between points A and B (as in Δp = pA - pB = ?). SG of oil is 0.8 . Provide solution in finding the height.
Based on the provided differential-type manometer, calculate the difference in the pressure between points A and B (as in Δp = pA - pB = ?).
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
A reservoir contains water has a vertical circular orifice 25.2mm diameter and is first plugged up to measure any displacing force, the tank is suspended in a particular way. The horizontal force is required to keep the tank in place on the removal of the plug. The opposite applied force to the orifice is 16.8N. The volume per time was found as 141lt/minute. It is assumed that the level of the water is maintained at a constant height of 2.785m above the orifice. Calculate Cc, Cv, and Cd for the orifice.
Estimate the height which water will rise in a capillary tube 12mm diameter. Use surface tension = 0.0728 N/m and gamma = 9810 N/m^3 Ans. No Capillary Action
Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140 KPa greater than at A. f= 0.019 Determine the head loss in meters. choices: 7.25, 5.27, 2.75, 7.52 Determine the flow rate in lit/sec. choices: 522.88, 822.55, 885.22, 228.55
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa