Answered: H.W.3/ A rectangular channel 10 m wide…

H.W.3/ A rectangular channel 10 m wide carries 15 cumecs. If the energy dissipated in the hydraulic jump is channel is 4.17 m, compute the basin type for dissipation.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem (1) Find the quantity of discharge q in meter cube per second per meter width for the…

A: To Determine Quantity of discharge, q in m³/s/m

Q: Estimate the constant rate of withdrawal from a 1375 hectare reservoir in a month of 30 days during…

Q: Determine the total seepage loss per meter length of the dam (in m/day/m). Given X = 18 m; Y = 4 m;…

A: From figure:NF=number of flow channels=4ND=number of equipotential depths=10we have…

Q: Q: The table below represents the elevation-area curve for a reservoir, the maximum storage is 32…

A: As a place or position of height, elevation is defined as height above the ground or another…

Q: Example 5.2 A 30 cm well penetrates 50 m below the static water table. After a long period of…

Q: QI. An unconfined aquifer of 0.15 specific yield, and surface area of 500 km. How long it will take…

A: surface area of aquifer A=500 km2drop in water h=5.0 m total volume of the aquifers V=…

Q: I. Draw the phreatic surfaces and determine the flow rates with and without the drainage blanket for…

A: Given:- k=kx=1.2 x 10-6cm/s slopes of upstream and downstream=1V:2H To find:- flow rates

Q: The hydraulic jump has a depth of 5 m at the downstream end, and the velocity is V2=1.75 m/s. If the…

A: NOTE: Due to some technical issue, formulation and equation writings is not possible. Hence, images…

Q: Water flows in a trapezoidal channel of 2 m width and side slope at 1:1. At upstream depth of 2 m,…

Q: Q2: A reservoir had 28 cm evaporation during April 2016 and an average surface area 25 km?. In that…

Q: Show that for uniform flow, channel bed slope, free water surface level and total energy line are…

A: Z1 = Datum headY1 = Kinetic head V22g = Velocity headBy energy equation,Y1 + Z1 + V122g = Y2 + Z2 +…

Q: A well with a diameter of 18 in. penetrates an unconfined aquifer that is 100ft thick. Two…

A: To Find :- Steady state discharge Q

Q: A 5 m wide rectangular channel carrying a discharge of 14 cumec. A hydraulic Jump occurs in such a…

A: Discharge (Q) =14 m3/s Depth before jump (d1) =0.3m g= 9.81 m/s2 Width of channel = 5m

Q: A tube well of 15 cm diameter penetrates fully an artesian aquifer 27 m thick. Determine…

Q: Problem 2. A well is located in a completely confined aquifer with a hydraulic conductivity of 12…

Q: To prevent downstream flooding, the maximum flow to be released from the catchment is set at 273…

Q: cm well penetrates 25 m below the static water table. After 24 hours oI pumping out at the rate of…

A: Given data in question Radius of well 20 cm Rate of pumping 800 lpm Radius of testing wells 20 m…

Q: 10.67 In a rectangular channel 4 m wide flow of 7.65 m/s the depth is 0.4 m. If a hydraulic jump is…

A: We have equation2q2g=y1y2y1+y2

Q: B- A 20cm diameter well penetrates fully a confined aquifer of thickness 25m .when the well is…

Q: A well 12‐in in diameter penetrates 108 ft below the static water table. After a long period of…

A: Data - h1=108-12=96 fth2=108-7.4=100.6 ftr1=57 ftr2=148 ft

Q: Calculate the volume of water in the dam at the end of the year assuming no outflows for downstream…

Q: A hydraulic jump occurs in a trapezoidal channel with slope of 1:1 and base width of 4 m. If the…

Q: A 300-mm diameter test well penetrates 27m below the static water table. Water is pumped at the rate…

Q: For a uniform flow with depth of 0.6 m and Froude number of 2.0 in a rectangular channel, the…

A: Given data: uniform flow. flow depth= 0.6 m Froude number (Fr)=2.0 rectangular channel.

Q: A 30 cm well is pumped at the rate of 1000 1pm. The transmissibility of the aquifer is o.015 m²/s.…

A: The given data is: Q=1000 Lps Q=1/60 m3/s x=120 m a=120 m T=0.015 m2/s r=80 m

Q: (B): For the concrete dam shown in figure below. The water heads are 16 m on the upstream side and 2…

A: Given Upstream water level = 16 m Downstream water level = 2m Horizontal permeability = 6×10^-3…

Q: A confined aquifer has a thickness of 85 ft. An 86-in diameter well drilled to the bottom of the…

A: To find discharge and velocity

Q: A 30 cm diameter well penetrates 25 m below the static watertable. After 24 hours of pumping @ 5400…

Q: Open Channels Water flows in a rectangular open channel at a depth of 0.75 m and a velocity of 3.2…

A: above given data d1 = .75m aand V1 =3.2 m/s

Q: A 0.5 km long pipe of diameter 0.45 m is connecting togeth er two reservoirs. If the difference in…

A: Given: Length of pipe, L = 0.5 km = 500 m Diameter of pipe, d = 0.45 m Difference in water level of…

Q: Determine the coefficient of permeability of a confined aquifer 8 m thick which gives a steady…

Q: Example 2.10 A rectangular channel has a width of 2.0 m and carriers a dis- charge of 4.80 m'/s with…

Q: A fully penetrating well of diameter 0.3 m is located in an unconfined aquifer of saturated depth 45…

Q: A hydraulic jump occurs in a rectangular channel that is 7 m wide. The initial depth is 0.8 m, and…

Q: A rectangular channel carries a dis-charge of 2 m/sec per meter width. If the loss of energy in the…

A: step 1-

Q: If a hydraulic jump occurring in a rectangular channel 2,5 m wide such that the depth after the jump…

Q: A 3.4-m square vertical tank 10 m high contains 3.9 m of oil (SG=0.77). A 82 mm diameter circular…

Q: A 60-cm-diameter well is located in an aquifer with a transmissivity of 125 m2/day and a storativity…

A: Given diameter = 60 cm =0.6 m Transmissivity T= 125 m2 / day Storativity S = 5*10-2Time = 1 year =…

Q: Example 7.3 A circular island of 600 m radius has an effective rainfall of 5 mm/day. A central well…

Q: A pipeline leads from one reservoir to another which has a water surface 10 m lower.For a discharge…

Q: Example 2: A flow net is plotted for a homogeneous earthen dam of height 22 m and freeboard 2.0 m.…

Q: What is the pumping rate (in m³/d) required to create a drawdown of 129 mm at 173.7 from the well…

A: step 1-

Q: A well 76 m deep is planned in an aquifer a transmissibility of 75 m?/day and storage coefficient of…

Q: fer to the cross section of the earth dam shown in the figure. Calculate the rate of seepage through…

A: Casagrande's method is a method used to find soil's liquid limit. Darcy's law can be used to…

Q: Q1. An unconfined aquifer of 0.15 specific yield, and surface area of 500 km². How long it will take…

A: Unconfined Aquifer An unconfined aquifer is an aquifer into which water leaks from the ground…

Q: Figure D shows a diagram of the flow net of water for the weir. if the permeability of the permeable…

A: Number of equipotential drops =9Number of FLow channels =5so,

Q: A concrete dam is 30 m long from upstream side to downstream end. The dam is situated on a…

A: Figure showing the flow net for seepage occurring beneath the dam…

Q: Example 4.4 A fully penetrating artesian well is pumped at a rate Q = 1500 m³/day from an aquifer…

Q: A well is planned for pumping a confined aquifer at a rate of 40.51 L/s. The hydraulic conductivity…

A: Given data: The thickness of the confined aquifer is H=55 m. The hydraulic conductivity of the…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

H.W.3/ A rectangular channel 10 m wide carries 15 cumecs. If the energy dissipated in the hydraulic jump is channel
is 4.17 m, compute the basin type for dissipation.
KH n T na
WASIII di Ler ine wOIr
i5 S.n.. Lype. rinu ne iengtn of
----.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A boiler feed booster pump supplies 0.0373 m3 /s of water at 1500 rpm. Its suction speed is 3.5 and net positive suction head available is 5m. Find safety margin of cavitation.
Two reservoirs ( Elev. 38.7m and Elev. 90.6m ) are connected by two pipelines 1-2 and 2-3 with a pump bridging the two pipelines. If the fluid (s.g = 0.81) flows at a rate of 174 L/s, what is the power given by pump? Assume head losses of 2.6 J/N from 1-2 and 5.5 J/N from 2 to 3
the system consists of 1000m of 50mm cast iron pipe, two 45° and 4 90° flanged long radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. Water flows at rate of 4.5 L/s from pt. 1 to the reservoir whose free surface lies 100m above pt.1. Kinematic viscosity is 1.02x10^-6 sqm/s and f=0.035. compute for: a.) reynolds number b.) total head lossv(m) c.) gage pressure at 1 to deliver water into the reservoir (kPa)
Q3/ The water levels in the two reservoirs A and B are 104.5 m and 100 m respectively above the datum. Pipe joins each to a common point D, where pressure is 98:1 kN/m”*2 gauge at above the joint point D and height is 83-5 m above datum. Another pipe connects D to another tank C. What will be the height of water level in C assuming the same value of ‘f’ for all pipes. Take friction co-efficient f = 0-0075. The diameters of the pipes AD, BD and CD are 300 mm, 450 mm, 600 mm respectively and their lengths are 240 m, 270 m, 300 m respectively. 100 m Your answer
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
A pump draws water (SG=0.998) from reservoir A and transport it to reservoir B, with the static Suctionhead 8m and static discharge head of 28 m. The diameter of the suction pipe is 15.24 cm, and the diameter of the discharge pipe is 4 in. The total head loss from A to B is 25% of TDH, and the head loss at the discharge line is 90% of the total headloss. If the pump capacity is 60 Ips, determine the following:a. Pump Break power if the efficiency is 82% b. Reading of the pressure gauge installed at the suction flange of the pump C. Reading of the pressure gauge installed at the discharge flange of the pump
Given the properties and elevations of the three reservoirs, if friction factor f, is 0.01 for all pipes,determine the followinga. Energy head at junctionb. Head loss of pipe-1c. Discharge of pipe-3
Earth dam homage material has the fllows data K=0.0005cm/sec level of top of the dem= 200m bed level of the dam =1.78m filter length=25m free beard=2.5mu/s slope=3:1 D/s slope =2.5:1 determine the phredic line for this dam and the discharge casing through the dam (casingrande of flownet)
Water is to be siphoned from a tank at the rate of 0.0892 m^3/s. The flowing end of the siphon pipe must be 4.27 m below the water surface. The lost head terms are 1.5V^2/2g from tank to summit of siphon and V^2/2g from summit to end of siphon. The summit is 1.52 m above the water surface. Find the pressure at the summit in kPa. 3 decimal places.
A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
A hydraulic jump is formed in a 4 m wide rectangular open channel at a short distance downstream of a control gate. The flow depth just downstream of the gate is 1.8 m and the outlet discharge is 134 m3 /s. The density of water is 1000 kg/m3 . Determine the flow depth downstream of the jump and the headloss in the jump. Express the headloss in kW per metre width. i need ansswer in 30 minutes thank u
1] A pump draws water from an open reservoir, with a static suction headof 26.24 feet, and lifts it to another open reservoir with a static discharge head of25 meters. The diameter of the suction pipe is 15.24 cm and the diameter ofdischarge pipe is 4.0 inches. The total head loss from A to B is 25 % of the totaldynamic head (TDH), and the head loss at the discharge side of the pump is 90 %of the total head loss. The pump capacity is 50 lps. Determine: a) the pump brakepower if the efficiency is 82 %; b) the reading of the pressure gauge installed atthe suction side of the pump; and c) the reading of the pressure gauge installed atthe discharge side of the pump.