The strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain on the Z axis of the structure. b) In this case, what is the strain type of the structure in the Z axis? Н-8 стL = 4 cma = 50°t = 5 mm%3D%3DSin?aVzxCos a (H/L - Cos a)The strain value of the structure in the same direction as a resultof the pull applied in the X axis from the bottom was measured as0.26 mm / mm. Under the same loading condition:a) Calculate the strain on the Z axis of the structure.b) In this case, what is the strain type of the structure in the Zaxis?

Answered: Image /qna-images/answer/7e3250a0-62c6-4a15-bc96-83b9f33b6365.jpg

H=8 cm L = 4 cm a = 50° t = 5 mm Sin?a Vz Cos a (H/ - Cos a) The strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain on the Z axis of the structure. b) In this case, what is the strain type of the structure in the Z axis?

H=8 cm L = 4 cm a = 50° t = 5 mm Sin?a Vz Cos a (H/ - Cos a) The strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain on the Z axis of the structure. b) In this case, what is the strain type of the structure in the Z axis?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.26P: - 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v...

See similar textbooks

Similar questions

A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
9- What strain will be produced by a stress of 40 x 106 N/m2, for a given modulus of elasticity 200GPa. a. 0.0008 b. 0.0002 c. 0.004 d. 0.002
A material is subjected to two mutually perpendicular strains ex=350x10-6, ey=50x10-6 with unknown shear strain. If the principal strain in the material is 420x10-6. Determine (A) unknown shear strain (B) the other principal strain (C) the direction of principal strains (D) the magnitude of the principal stresses E=200GN/m2 and poison's ratio is 0.3
Determine the strain if a rod is experiencing a stress of 70,000kPa with a modulus of elasticity of 175 GPa.a. 300 x 10−6b. 400 x 10−6c. 500 x 10−6d.. 600 x 10−6
The state of plane strain at a point has strain components of Px = -400(10-6), P y = 200(10-6), and gxy = 150(10-6), Fig. a. Determine the maximum in-plane shear strain and the absolute maximum shear strain.
Question 3 3. A string 4 mm in diameter has original length 2 m. A force of 200 N. pulls the string. If the final length of the spring is 2.02 m, determine: (a) stress (b) strain (c) Young's modulus.
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Strain of Silly Putty: Initial length (L0): 2.85 cm Final length (L): 8.50 cm Strain: % (show calculation below): (Please type answer no write by hend)
If the shear modulus of a material is 120GPa & the bulk modulus is 140 GPa, then Young’s modulus is------ a. 820 GPa b. 280 Pa c. 280 GPa d. 820 Pa
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and ismade from a homogeneous material. The length (L) of the rod is 1.75 m andYoung’s Modulus for the material (E) is 250 GPa. When the rod is placed undertension it experiences deformation and a stress (?) of 650 MPa. Calculate thefollowing:(i) Strain energy (U) to 2 decimal places in Joules.(ii) Strain energy per unit volume (U/V) in J/m3.(iii) The change in length ∆L to 2 decimal places in mm.(iv) The strain (?) due to deformation to 2 significant figures