HAND CALCULATION: An RL Circuit consists of a resistor and an inductor in series as displayed in the figure below. t = 0 + 를 V R ele L RL circuit diagram Using Kirchhoff's Voltage Law, the following equation can be found to describe the circuit: Ri + L = V The inductance is L = 0.1 H. You have seven resistors: 10, 15, 22, 33, 47, 68, and 100N. Due to a manufacturing defect, the voltage source, V , can output anywhere from 6-8 Volts. If the steady-state current must be between 0.08 and 0.2 A, which resistor(s) can you use in the circuit?

HAND CALCULATION: An RL Circuit consists of a resistor and an inductor in series as displayed in the figure below. t = 0 + 를 V R ele L RL circuit diagram Using Kirchhoff's Voltage Law, the following equation can be found to describe the circuit: Ri + L = V The inductance is L = 0.1 H. You have seven resistors: 10, 15, 22, 33, 47, 68, and 100N. Due to a manufacturing defect, the voltage source, V , can output anywhere from 6-8 Volts. If the steady-state current must be between 0.08 and 0.2 A, which resistor(s) can you use in the circuit?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Capacitance= 4uF , Hence time constant is 5.33μs For the capacity value, calculate the estimated time to come to the final state.Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.
Design a single circuit element containing one inductor, one capacitor and one resistor with v(t) of = vt=4+2e-3tV and it=-3e-3tA for t>0 . Also specify the value of the inductance, capacitance and the resistance of the tree element
Capacitance= 4uF2) Determine the time constant of the circuit for the capacities 3) For the capacity value, calculate the estimated time to come to the final state.4) Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.
A circuit consists of switches that open or close at t=0, resistances, dc sources, and a single energy storage element, either an inductance or a capacitance. We wish to solve for a current or a voltage x(t) as a function of time for t≥0. Write the general form for the solution. How is each unknown in the solution determined?
a series r-c circuit takes a current whose equation is i=0.85sin(754t+pi/4) when connected to a source of emf having the equation e=340sin754t. calculate the capacitance of the capacitor, circuit power factor, and power.
Consider the circuit below. a) Calculate the equivalent capacitance Ceq (show all steps) b) What is the potential difference across C4?
An RL circuit has a resistance of 20 ohms, and inductance of 1.5 H and applied emf of 12 volts, and an initial current of 6 amperes. FInd the current in the circuit at any time t.
Can you find the total energy developed in the circuit? Explain.
Using the 0.68 kilo Ohms, 3.3mH inductance, and 5V source, compute for the theoretical voltages across the resistor and inductor for 10 kHz and 60 kHz. Show the step-by-step computation. Express the voltages in polar form.
In the Figure Q3(c), determine the value of R for which the steady-state energy storedin the inductor will be 0.25J.
The circuit shown in the attached image contains a voltage source with emf ε = 2.99 V, a resistor with resistance R = 135 kΩ, and a capacitor with capacitance C = 612 nF. When switch S is set to position a, the three circuit elements are in series. When the switch is in position b, the battery is excluded from the circuit. The switch is initially moved to position a, where it remains for a sufficiently long time that the capacitor is fully charged. The switch is now moved to position b. What is the magnitude of the instantaneous current, in amperes, through the resistor the instant the switch makes contact with terminal b? With time meausred the instant that switch S is closed in position b, calculate the time, in seconds, when the charge on the capacitor is one-half of its maximum value. Calculate the current through the resistor, in amperes, at time t = 155.5 ms after the switch is closed in position b.
How can four 100 kΩ resistors be connected so that the equivalent resistance of the four equals 250 kΩ? Sketch the arrangement, describe the resistor arrangement in words, and justify your picture by calculating the equivalent resistance. Repeat this part of the question with four 100 F capacitors and an equivalent capacitance of 75 F.