has a diameter d of 30 mm and strikes a from a fixed nozzle flat plate at angle u of 30° to the normal to the plate. The velocity of the jet v is 5m/s, and the surface of the plate can be assumed to be frictionless. Calculate the force exerted normal to the plate if the plate is moving with velocity u of 4m/s in the same direction as the jet. V 30% P m

has a diameter d of 30 mm and strikes a from a fixed nozzle flat plate at angle u of 30° to the normal to the plate. The velocity of the jet v is 5m/s, and the surface of the plate can be assumed to be frictionless. Calculate the force exerted normal to the plate if the plate is moving with velocity u of 4m/s in the same direction as the jet. V 30% P m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assuming that the fluid enters to the pump with no shock / no swirl, construct the velocity triangles at both inner and outer diameters of the impeller for the case where the blade angle at the outlet is: β2 = 90o, and β2 = 130o
Water enters vertically and steadily at a rate of 60 L/s into the sprinkler shown, with unequal arms and unequal discharge areas. The smaller jet has a discharge area of 3 cm2 and a normal distance of 50 cm from the axis of rotation. The larger jet has a discharge area of 5 cm2 and a normal distance of 35 cm from the axis of rotation. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating.
A jet of water from a nozzle is deflected through an angle θ = 60° from its original direction by a curved vane which it enters tangentially (see Fig. 5.5) without shock with a mean velocity C1 of 30 m s−1 and leaves with a mean velocity C2 of 25 m s−1. If the discharge A from the nozzle is 0.8 kg s−1, calculate the magnitude and direction of the resultant force on the vane if the vane is stationary.
The pipe elbow below discharges water at rate of SN/100 (m3/s) into the atmosphere at section 2. The total volume of the passage between sections 1 and 2 is equal to 0.2 m3 and the total mass of the elbow material between sections 1 and 2 is equal to 10 x SN (kg). Neglect any friction losses. Calculate the horizontal and vertical forces acting on the elbow. Also, calculate the resultant force and angle of force on the elbow. ****SN=21
As shown in the figure, the water entering axially into a turbine wheel emerges at a velocity of V = 5 m / s among 20 blades with a thickness of 5 mm. Calculate the water velocity at the impeller inlet.
Find the force exerted by a jet of water of diameter 75 mm on a stationary flat plate, when the jet strikes the plate normally with velocity of 20 m/s.
A 100-ft3 /s wáter jet hits a horizontally lying stationary splitter, such that half of the mass flow is diverted one way and the other half is diverted the other way, and both streams have a uniform velocity of 18 ft/s. The deflection angle of the splitter is 45 degrees as shown. Obtain (a) the cross-sectional area of the jet and (b) the horizontal (x-y) components of the force required to hold the splitter in place.
A jet of water with a diameter of 100 mm flows vertically until it meets a solid vane that deflected it at an angle of 180°. The initial velocity of the jet is 20 m/s. As a result of friction, the velocity of the jet leaving the vane is 15 m/s. Assuming the fluid is at atmospheric pressure throughout and neglecting the gravity effects, calculate the magnitude of the force exerted by the water on the vane. (water density 1000 kg/m3)
A converging nozzle having an exit diameter of 30 mmmm is connected to the large tank (Figure 1). The absolute pressure outside the tank is 102 kPa If the temperature of the air in the tank is 20∘C and the absolute pressure is 580 kPa, determine the mass flow from the tank in kg/s
A jet strikes a stationery curved vane without shock and is deflected 150° from its original direction. The discharge from the jet is 0.68kg/s and the velocity is 24m/s. Assume that there is no reduction of relative velocity due to friction and determine the magnitude and direction of the
A jet of water whose diameter is 5cm strikes a fixed cup with a velocity of 9.45m/s and is deflected by 165 degree. The jet leaves with a velocity of 30m/s . if the cup offers a reactive force of 26.5N to the jet when the flow rate was 980 N/min. Determine the ratio of a) Actual to theoretical forces of the jet. b) Velocities at outlet and inlet. Assume any missing data.
The pump in the figure draws water from an 8-in. suction pipe and discharges through a 6-in. pipe in which the velocity is 12 ft per second. The pressure is -5 psi at A in the suction pipe. The 6-in pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 6 ft above A and 20 horsepower is delivered to the pump? Assume that the pump operates at 70 percent efficiency and that the frictional loss in the pipe between A and C is 10 ft.