he water surface temperature at 20 ° C is kept constant at 80 ° C, 1 m wide and 3.6 m long It flows over a plate with a free flow velocity of 1.2 m / s. a) Determine the point where the flow passes into turbulence b) Average convection heat transfer coefficient on the plate, h (W / m2K) c) Rate of heat transfer from this plate to water ?̇ (W)

he water surface temperature at 20 ° C is kept constant at 80 ° C, 1 m wide and 3.6 m long It flows over a plate with a free flow velocity of 1.2 m / s. a) Determine the point where the flow passes into turbulence b) Average convection heat transfer coefficient on the plate, h (W / m2K) c) Rate of heat transfer from this plate to water ?̇ (W)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.55P

See similar textbooks

Similar questions

Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Show that the two-dimensional laminar fl ow pattern withdp/dx =0u = U0(1 - eCy)υ =υ0 < 0is an exact solution to the boundary layer equations .Find the value of the constant C in terms of the fl ow parameters.Are the boundary conditions satisfi ed? What mightthis fl ow represent?
Engine oil at 100°C flows on the top surface of a 1-m-long flat plate maintained at 20°C. The oil’s freestream speed (u infinity) is 0.1 m/s. Find the engine oil properties from the table A.5 A. Evaluate the Reynolds number, local convection coefficient, heat flux and shear stress at the end of the plate (x = L). Is the air flow laminar or turbulent over the plate?B. Evaluate the average convection coefficient, average heat flux, average shear stress and drag force over the plate.
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.72 W/m deg C, Re=3840000, and Pr=0.7)?
Q1) Briefly explain laminar, transition and turbulent flow based on boundary layer separation.
Qs. An aircraft is flying in level flight at a speed of 200 km/h through air (density, p = 1.2 kg/m³, and viscosity, μ = 1.6 x 10-5 N-s/m²). The lift coefficient at this speed is 0.4 and the drag coefficient is 0.0065. The mass of the aircraft is 800 kg. The effective lift area of the aircraft
Fluid from a large reservoir at temperature T 0 fl ows into acircular pipe of radius R . The pipe walls are wound with anelectric resistance coil that delivers heat to the fl uid at a rateq w (energy per unit wall area). If we wish to analyze thisproblem by using the full continuity, Navier-Stokes, andenergy equations, what are the proper boundary conditionsfor the analysis?
Air is flowing naturally over a cylinder of D=(15) cm. Air has thermal conductivity 0.027W/mK, kinematic viscosity 1.9*10-5 m2/s, Rayleigh number 108, and Prandtl number0.72. Find the Nusselt number
Distinguish between One, two and three-dimensional flow with one example
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Heat transfers Water (T= 10 C, , k=0.644 W/m.C, υ = 5.54× 10^-7 m2/s, Pr=3.55), flow over plate 1m x 1m , with velocity 2 m/s. the plate surface temperature is 90 C. Give the answer for the following: Nu number equal to Total heat transfer The flow type The average heat transfer coefficient
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)? Round your answer to 2 decimal places.