SEATWORK The figure as shown, ADD the last 2 digits of your i.d. number in the load P. Student i.d. No. 20201234 Ex: P = 50+34 = 84KN 1. Compute the Area of bronze that will not exceed a stress in bronze of 95 MPa and load P is 50KN. 2. Compute the Area of aluminum that will not exceed the a stress of 100 MPa and load P is 75 KN. 3. Compute the Area of steel that will not exceed the stress of 150 MPa and load P is 48KN. Bronze Aluminum Steel SUPPORT 4P P 2P

SEATWORK The figure as shown, ADD the last 2 digits of your i.d. number in the load P. Student i.d. No. 20201234 Ex: P = 50+34 = 84KN 1. Compute the Area of bronze that will not exceed a stress in bronze of 95 MPa and load P is 50KN. 2. Compute the Area of aluminum that will not exceed the a stress of 100 MPa and load P is 75 KN. 3. Compute the Area of steel that will not exceed the stress of 150 MPa and load P is 48KN. Bronze Aluminum Steel SUPPORT 4P P 2P

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? α=11.7x〖10〗^(-6)/°C and E = 200GPa. See figure 06
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
The polymer bar shown in the figure below has a width of b=55b=55 mmmm, a depth of d=104d=104 mmmm, and a height of h=274h=274 mmmm. At a compressive load of P=120P=120 kNkN, the bar height contracts by Δh=−2.60Δ⁢h=-2.60 mmmm, and the bar depth elongates by Δd=0.36Δ⁢d=0.36 mmmm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson’s ratio. (c) the change in the bar width bb.
Strength of materials - ENGR 3321 The answer should be: 17.68 kN; 11.8 MN/m2 compressive
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
Give me the solution of these with these answers: 2. ?? = 107.725 MPa 3. the shear stress in the anchorbolts. Ans: ? = 91.44 Mpa
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.