HOME WORK 1. Calculate the maximum and minimum limits for both the shaft and hole in the following; using the tables for tolerances and name the type of fit obtained: (a) 45H8/d7 (b) 180H7/n6 (c) 120H7/s6 (d) 40G7/h6 (e) 35 C11/h10 2. A schematic representation of basic size and its deviations are given in Fig. below Calculate the following in each case for a shaft of 50 mm basic size: (a) Upper deviation (b) Lower deviation (c) Tolerance (d) Upper limit size (e) Lower limit size +40 +30 +24 +10 0 0 -7 (a) (b) (C) (d) -20 -40 (e)

HOME WORK 1. Calculate the maximum and minimum limits for both the shaft and hole in the following; using the tables for tolerances and name the type of fit obtained: (a) 45H8/d7 (b) 180H7/n6 (c) 120H7/s6 (d) 40G7/h6 (e) 35 C11/h10 2. A schematic representation of basic size and its deviations are given in Fig. below Calculate the following in each case for a shaft of 50 mm basic size: (a) Upper deviation (b) Lower deviation (c) Tolerance (d) Upper limit size (e) Lower limit size +40 +30 +24 +10 0 0 -7 (a) (b) (C) (d) -20 -40 (e)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which variant of defining dimensions (A or B) would allow a higher overall part length tolerance, if the title block of the drawing holds an entry “General tolerances according to ISO 2768-m)”? Explain the reason for your answer.
1. Calculate the tolerances and allowances for a shaft with a diameter of 40 mm with a tolerance area k and a tolerance quality number 6, paired with a hole of the same diameter as the shaft and a tolerance area H with a tolerance quality 7. Also draw these tolerances schematically. ( answer in 20 minutes very needed thank u )
A 30 mm diameter hole is made on a turret lathe tothe limits, 30.035 and 30.00. The followingtwo grades of shafts are used to fit in the hole:(a) φ29.955mm and 29.925mm, and (b) φ30.055mm and30.050mm.Calculate the maximum tolerance, clearance and indicatethe type of fit in each case by a sketch.ii) Suggest suitable fits and their letter and tolerancegrades for the components
Use BS 4500A:1970 to determine the dimensional tolerance on the critical diameters in Gear Sub- assembly. The following tolerance should be determined (the limits and fits at each interface will be provided by Canvas): i. Bush & Shaft: Critical Diameter is 35 mm; (H8/f7) ii. Housing & Bush: Critical Diameter is 45 mm; (H7/s6) iii. Gear & Shaft: Critical Diameter is 20 mm (for the Right Gear) (H7/k6)
In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70 (+0.04 )/(+0.00 ) mm and Shaft = 70 (-0.04)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Research and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Explain how this tolerance is defined
Refer to the 1.914 dimension. A) Where is the tolerance specified ? _________________________________ B) What is its tolerance ? ________________________________C) What is the MMC? ______________________________ D) What is the LMC? _______________________________
Given a hole with a size dimension of Ø.875±.003 and a positional tolerance of.002 at MMC, what is the boundary that takes into consideration the combined effect of feature size at MMC and the geometric tolerance? .870 .874 .876 .880
Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm, according to the H9 limit deviation (∅25H9). ES=-12.7 mkm, Eİ=+0 mkm. Determine the basic size, tolerance and limit dimensions.
Refer to the 1.914 dimension. B) What is its tolerance ? ________________________________C) What is the MMC? (maximum material condition) ______________________________ D) What is the LMC(least material condition)? _______________________________
Please Fill In the blanks where I have marked red X's using the questions and Image below. 1. On the drawing above, before any geometric controls are applied, what is the coaxility tolerance is implied between the diameters? 2. On the part above, apply datum feature symbols to create a datum axis A-B by using the right and left diamters. 3. Apply a position coaxility between the right and left diamter of 0.1 at MMC. 4. Apply a position tolerance to the large center diameter within a diameter of 0.3 in relation to the single datum axis established by both datum features A and B.
Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 40 (+0.06 )/(+0.00 ) mm and Shaft = 40 (-0.07)/(-0.015) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.