HW1: A gas flows through a horizontal pipe with cross-sectional area of 30 cm². At certain point, gauge pressure is 300 kpa when the temperature is 20 °C. At another point, the cross-sectional area is 15 cm² and the gauge pressure is 250 kpa. If the mass flow rate was 0.15 kg/s, find the velocities at these points? Assume isothermal process and take Patm as 100 kpa.

HW1: A gas flows through a horizontal pipe with cross-sectional area of 30 cm². At certain point, gauge pressure is 300 kpa when the temperature is 20 °C. At another point, the cross-sectional area is 15 cm² and the gauge pressure is 250 kpa. If the mass flow rate was 0.15 kg/s, find the velocities at these points? Assume isothermal process and take Patm as 100 kpa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters a horizontal turbine at 350 lbf/in 2 absolute,580 ° C, and 12 ft/s and is discharged at 110 ft/s and 25 ° Csaturated conditions. The mass fl ow is 2.5 lbm/s, and theheat losses are 7 Btu/lb of steam. If head losses are negligible,how much horsepower does the turbine develop?
The volumetric flowrate of CCl4 (? = 0.659 g/cm3) in a pipe is 5.39 L/s. Find:a.the mass flow rate of the CCl4,b.the molar flow rate of the CCl4, andc.if it enters and exits to an irregular pipe with the inlet and outlet pipe diameters are 2.00 in and 8.00 in, respectively, the exit velocity.
at point a in pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. at point B, 2m higher than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. need answer please
An 8-in model pump delivering 180°F water at 800 gal/minand 2400 r/min begins to cavitate when the inlet pressureand velocity are 12 lbf/in2 absolute and 20 ft/s, respectively.Find the required NPSH of a prototype that is4 times larger and runs at 1000 r/min.
A soft drink (mostly water) flows in a pipe at Asia Brewery with a mass flow rate that would fill 220 0.355-L cans per minute. At point 2 in the pipe, the gauge pressure is 152kPa and the cross-sectional area is 8.20cm2. At point 1, 1.35 m above point 2, the cross-sectional area is 2.20 cm2. Find the gauge pressure at point 1.
Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.16 cm water gage. The duct diameter is 1.22 m, the barometric pressure 99.4 kPa and the gage flt*d temperature and air temperature are 30 C. What is the total pressure against which the fan will operate in cm of water?
Air flows isentropically through a channel. From two points inside this channel 1st speed 240 m / s, temperature 320 K and pressure 170 kPa. At the 2nd point, the speed is 290 m / s and the pressure is 135 kPa. a-) Stop temperature at first point, stop pressure, stop density, Mach number, maximum speed and critical point speed b-) find the stopping pressure of the second point.
In Fig. water exits from a nozzle into atmosphericpressure of 101 kPa. If the fl ow rate is 160 gal/min and frictionis neglected, what is the gage pressure at section 1?( a ) 1.4 kPa, ( b ) 32 kPa, ( c ) 43 kPa, ( d ) 29 kPa, ( e ) 123 kPa
1) When an incompressible fluid flows through a restricted (narrower) portion of a pipe, mass flow is preserved, so it: sloshes back and forth. must speed up. remains at constant speed slows down. creates a shock wave. 2) When an incompressible fluid moves from a wider pipe into a narrower one, it speeds up. This means that the wider portion must do work on the fluid (to accelerate it), and therefor the pressure there... goes to zero. is lower than in the narrow portion. is higher than in the narrow portion. is the same as in the narrow portion. cannot be calculated. 3) Normally, when the temperature of a solid, liquid, or gas increases, it expands, i.e., its volume V increases (and its mass density: ρ = m /V decreases). Because of its relatively strong hydrogen bonds, water ice forms an orderly, hexagonal lattice structure that requires the molecules to be about 9% further apart than when in the liquid phase, which…
The inlet section of a vacuum cleaner is a rectangle 1 in x 5 in.The blower is able to provide suction at 25 ft3/min. Assuming theair density is 1.2 kg/m3, what is the mass flow of air in kg/s?
Please solve it correctly,Urgent. Question: The discharge pressure of a water pump is 9, 000 kPa. The temperature is 150 deg deg C and density is 917 kg/m3. What is the equivalent pump head in meters? A. 11.005 m B. 1,000.5 m C. 1,050.5m D. 1, 100.5 m
A worker in a children's playground is cleaning a slide with a hose. She observes that a horizontal stream directed into the low end climbs to a point 14 ft above the nozzle. What is the nozzle velocity of the stream in ft/s?