Homework 1 The simple beam AE shown in the Figure (1) supports a concentrated loads. Determent the following: 1-Reactions in points A and E 2- Shear force at each points 3- Bending moment at each points 4- Draw the shear-force and bending-moment diagrams for this beam. t S5m —I 20[—;5 m—-l-_S m:j Figure (1) Homework 1The simple beam AE shown in the Figure (1) supports a concentratedloads. Determent the following:1-Reactions in points A and E2- Shear force at each points3- Bending moment at each points4- Draw the shear-force and bending-moment diagrams for this beam.35 kN20 kN|20 kNBD5 m5 m.5 m20 mFigure (1)

The shear force diagram represents the shear force at every section of the beam.Shear force at any…

Homework 1 The simple beam AE shown in the Figure (1) supports a concentrated loads. Determent the following: 1-Reactions in points A and E 2- Shear force at each points 3- Bending moment at each points 4- Draw the shear-force and bending-moment diagrams for this beam. 35 kN 120 kN 20 kN B D E 5 m- 20 m 5 m 5 m

Homework 1 The simple beam AE shown in the Figure (1) supports a concentrated loads. Determent the following: 1-Reactions in points A and E 2- Shear force at each points 3- Bending moment at each points 4- Draw the shear-force and bending-moment diagrams for this beam. 35 kN 120 kN 20 kN B D E 5 m- 20 m 5 m 5 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.32P: Two identical, simply supported beams AB and CD are placed so that they cross each other at their...

See similar textbooks

Similar questions

A wood box beam is constructed of two 260 mm × 50 mm boards and two 260 mm × 25 mm boards (sec figure). The boards are nailed at a longitudinal spacing. b = 100 mm. If each nail has an allowable shear force F = 1200 N. what is the maximum allowable shear force Vmax?
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
Two identical, simply supported beams AB and CD are placed so that they cross each other at their midpoints (sec figure). Before the uniform load is applied, the beams just touch each other at the crossing point. Determine the maximum bending moments (mab)max* and (MCD)max beams AB and CD, respectively, due to the uniform load if the intensity of the load is q = 6.4 kN/m and the length of each beam is L = 4 m.
The horizontal beam ABC of an oil-well pump has the cross section shown in the figure. If the vertical pumping force acting at end C is 9 kips and if the distance from the line of action ofthat force to point B is 16 ft, what is the maximum bending stress in the beam due to the pumping force?
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 0,88 in. and h1 = 0.80 in. The maximum allowable bending stress in the metal beam is emax = 60 ksi, and the bending moment is M = 600 lb-in. Determine the minimum permissible width bminof the beam.
The deflection curve for a simple beam AB (sec figure) is given by v=q0L44EIsinxL Describe the load acting on the beam. Deter mine the reactions RAand RBat the supports, Determine the maximum bending moment Mmax.
The three beams shown have approximately the same cross-sectional area. Beam 1 is a W 14 X 82 with flange plates; beam 2 consists of a web plate with four angles; and beam 3 is constructed of 2 C shapes with flange plates. Which design has the largest moment capacity? Which has the largest shear capacity? Which is the most economical in bending? Which is the most economical in shear? Assume allowable stress values are: = 18 ksi and ra=11 ksi. The most economical beam is that having the largest capacity-to-weight ratio. Neglect fabrication costs in answering parts (c) and (d) above. Note: Obtain the dimensions and properties of all rolled shapes from tables in Appendix F.
For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending moment acting on section 1 in terms of the distance x (0 < x< L). [Note: Case 1 results in the conventional V- and M-diagrams, in which the loads are fixed and the location of the section varies; the diagrams for Case 2 (called influence diagrams) show the variation of V and M at a fixed section as the location of the load is varied]
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
A propped cantilever beam is loaded by two different load patterns (see figures a and b). Assume that El is constant and the total beam length is L. Find expressions for reactions at Â and B for each beam. Plot shear and moment diagrams. Assume that a = L/B.
A steel beam is built up from a W 410 × 85 wide flange beam and two 180 mm X 9 mm cover plates (see figure). The allowable load in shear on each bolt is 9.8 kN. What is the required bolt spacing s in the longitudinal direction if the shear force V = 110 kN Noie: Obtain the dimensions and moment of inertia of the W shape from Table F-l(b).
A frame ABCD is constructed of steel wide-flange members (W8 x 21; E = 30 x ID6 psi) and subjected to triangularly distributed loads of maximum intensity q0acting along the vertical members (see figure). The distance between supports is L = 20 ft and the height of the frame is h = 4 ft. The members are rigidly connected at B and C. Calculate the intensity of load q0 required to produce a maximum bending moment of 80 kip-in. in the horizontal member BC. If the load q0 is reduced to one-half of the value calculated in part (a), what is the maximum bending moment in member BC? What is the ratio of this moment to the moment of 80 kip-in. in part (a)?