Direction: Solve the following problems neatly and systematically and include free body diagrams. 1-5. For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Neglect the weight of the beam. "1 A A Wo L Problem 1 L Problem 3 A B Wo B 2 m- B A 80 kN/m Problem 5 2 m- L Problem 2 B Problem 4 B X

Direction: Solve the following problems neatly and systematically and include free body diagrams. 1-5. For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Neglect the weight of the beam. "1 A A Wo L Problem 1 L Problem 3 A B Wo B 2 m- B A 80 kN/m Problem 5 2 m- L Problem 2 B Problem 4 B X

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.6P: A beam with a sliding support at B is loaded by a uniformly distributed load with intensity q. Use...

See similar textbooks

Similar questions

Determine the bending moment M in the pinned-end column with eccentric axial loads shown in the figure. Then plot the bending-moment diagram for an axial load P = 0.3Pcr. Note: Express the moment as a function of the distance x from the end of the column, and plot the diagram in nondimensional form with M/Pe as ordinate and x/L as abscissa.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
The horizontal beam ABC of an oil-well pump has the cross section shown in the figure. If the vertical pumping force acting at end C is 9 kips and if the distance from the line of action ofthat force to point B is 16 ft, what is the maximum bending stress in the beam due to the pumping force?
Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
The equation of the deflection curve for a simply supported beam is v(x)=q024EI(2Lx3x4L3x) Derive the slope equation of the beam. Derive the bending-moment equation of the beam. Derive the shear-force equation of the beam. Describe the loading acting on the beam.
A beam with a sliding support at B is loaded by a uniformly distributed load with intensity q. Use the method of superposition to solve for all reactions. Also draw shear-force and bending-moment diagrams, labeling all critical ordinales.
A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force, shear-force, and bending-moment diagrams for ABC.
The shear-force diagram for a beam is shown in the figure. Assuming that no couples act as loads on the beam, determine the forces acting on the beam and draw the bending-moment diagram.
The beam AB shown in the figure supports a uniform load of intensity 3000 N/m acting over half the length of the beam. The beam rests on a foundation that produces a uniformly distributed load over the entire length. Draw the shear-force and bending-moment diagrams for this beam. Repeat part (a) for the distributed load variation shown in Fig. b.
A propped cantilever beam of a length L is loaded by a concentrated moment M0at midpoint C Use the second-order differential equation of the deflection curve to solve for reactions at A and B. Draw shear-force and bending-moment diagrams for the entire beam. Also find the equations of the deflection curves for both halves of the beam, and draw the deflection curve for the entire beam.
A simple log bridge in a remote area consists of two parallel logs with planks across them (see figure). The logs arc Douglas fir with an average diameter 300 mm. A truck moves slowly across the bridge, which spans 2.5 m. Assume that the weight of the truck is equally distributed between the two logs. Because the wheelbase of the truck is greater than 2,5 m, only one set of wheels is on the bridge at a time. Thus, the wheel load on one log is equivalent to a concentrated load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. Determine the maxi mum permissible wheel load W based upon (a) an allowable bending stress of 7.0 MPa and (b) an allowable shear stress of 0.75 MPa.