Please help with homeworkNB:Also show me the gear train ratio, output speed of gear D, torque available on the output shaft, distance between the shafts for Gears C and D [mm], A compound spur gear train is made up of a set of gears asindicated in the sketch using an input gear A and with a moduleof 6 and a contact angle of 20°. Calculate the:a. output speed and direction of rotation for Gear D,b. torque available on the output shaft if the input shaft isprovided with 20kW at 2150 rpm,c. distance between the shafts for Gear C and Gear D.122412BC18D

Answered: Image /qna-images/answer/76e9792f-e651-477e-8a11-d48458f68d3e.jpg

Answered: homework NB: Also show me the gear…

homework NB: Also show me the gear train ratio, output speed of gear D, torque available on the output shaft, distance between the shafts for Gears C and D [mm],

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design A two stage spur gear reduction unit with 20- Deg full depth involute teeth. The input shaft rotates at 1440 rpm and receives 10 kW power. The speed of the output shaft should be approximately 180 rpm plus minus 5 rpm , All gears are made of steel and have the same module . Determine appropriate number of teeth of the gears in the unit .
Two meshing spur gears with 20° pressure angle have a module of 4 mm. The centre distance is 220 mm andthe number ofteethonthe pinionis 40. What shouldbethe new centre distance so that pressure angle is increased to 22°?
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
Design a pair of straight bevel gears to transmit 5.0 hp at a pinion speed of 850 rpm. the gear speed should be approximately 300 rpm. consider both strength and pitting resistance. the driver is a gasoline engine, and the driven machine is a heavy-duty conveyor.
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
A set of gears is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor, depicted below. The gear on the motor shaft is a 10-pitch pinion, has 18 teeth, and drives at 1200 rpm clockwise. The driven gear has 72 teeth. The motor has failed and is to be replaced with the only motor available, a 600 rpm motor with an 8-pitch pinion. Specify the set of commercially available 20⁰ spur gears, by number of teeth (N3and N4), that would result in the same conveyor speed and can be used without modification to the mounting (the center distance must not change). Find the number of teeth N3 on the pinion (drive) gear (teeth): Find the number of teeth N4 on the driven gear (teeth):
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
1. A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Determine: a. If there is interference b. If the center distance was increased by 3mm, find the backlash produced c. length of action and contact ratio
Design a pair of plastic gears to drive a small band saw, using the following data: The input is from a 0.5hp electric motor rotating at 1160 rpm. The pinion is mounted on its 0.75 in diameter shaft. The gear is rotating at 250 rpm. For design purposes, consider taking Np=18 (number teeth in pinion) and Pd = 12 (diametral pitch). In this case, the acceptable number of teeth in the gear should be: NG=58 teeth NG = 93 teeth NG = 84 teeth NG = 70 teeth
A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic loa
(b)A pair of straight bevel gears has a velocity ratio of 2:1. The pitch circle diameter of the pinion is 80 mm at the large end of the tooth.A5KW power is supplied to the pinion which rotates at 800 rp.m. The face width is 40 mm and the pressure angle is 20. Calculate the tangential ,radial and axial components of the resultant tooth force acting on the pinion
A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Find : $ if there is an interference $length of action and contact ratio $ if centher ditance was increased by 3mm, find backlash produced