Horizantal P= 180 NE a) While steadily pushing the machine up on an incline surface, a person exerts 180 N force P as shown. Determine the components of P which are parallel and Perpendicular to the incline surface? 10 15

Horizantal P= 180 NE a) While steadily pushing the machine up on an incline surface, a person exerts 180 N force P as shown. Determine the components of P which are parallel and Perpendicular to the incline surface? 10 15

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.71P: The force F=5i+12j+4k lb is applied to the handle of the door. Determine the orthogonal component of...

See similar textbooks

Related questions

Q: Q3/ Determine the resultant of the force system shown in Fig. 224 300 30 361

A: It is required to determine the resultant force

Q: The roof truss shown is typically used for solar energy purposes, where a near normal angle of…

Q: The rope AB exerts a 45 Newton force T on collar A. Determine the magnitude of vector component of T…

A: Concept Of Vector Addition And Multiplication Is Used.

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 820-N load is…

Q: Determine the resultant force for the forces system shown in * fig 37 120N 60 N 20 200MM looN

Q: Determine P and θ so that the three forces shown are equivalent to the single force Rx = 87.32 kN.…

Q: the end of the 22-m-long crane boom, the towline exerts a force of P = 4 kN. If 0 = 30°, what is the…

Q: Q3/ Determine the resultant of the force system shown in Fig. 224 300 30 3 361

Q: Q1/ The Forces act on blot A as shown. Determine all component of those forces? 110N

A: It is required to determine components of each forces

Q: Q3: Find the magnitude, location and slope of the resultant of the force system shown below. k=30 EN…

Q: A- In Fig.A, Replace the loading system by an equivalent resultant force and specify where the…

A: For the given system of forces To determine Replace the loading by an equivalent resultant force…

Q: Determine the realtant R of the two forces applied to the bracket. Write Rin terms of unit vartors…

A: First writing the given two forces in vector form along x and y direction,

Q: 10. The three forces, each of magnitude F, are applied to the crate. Determine F so that the three…

A: To determine the force F.

Q: Four forces are exerted on the eyebolt as shown. If the resultant on the bolt is a direct pull of…

A: given ;

Q: Determine the components of force P 40 kN along x and y as shown in Fig.?. (16) Ps4oKN 30

A: Given Data: Force P=40 KN Angle θ=30°

Q: 4. The Distributed load is shown in the figure. Determine; a. the magnitude of the equivalent 42 N/m…

Q: Determine the magnitude of moment (Nm) of the 366-N force about point A if x = 0.53 m, y = 0.66 m,…

Q: Q6 The forces FI, F2, and F3. all of which act on point A of the bracket, are specified in three…

Q: During a steady right turn, a person exerts the forces shown on the steering wheel. Note that each…

A: As per given question F1=580N L1=0.08m We have determine moment at O

Q: Determine the resultant of the force system shown in fig. and its diarection if ?F1= 750 N and the…

A: solved

Q: H.W1:The 624 N force is a resultant of two force P & Q shown in fig. determine these forces . 624 N…

A: As given that force (R) 624 N is resultant of the force P and Q. So the inclination of the P and Q…

Q: (25) 1. Draw the free body diagrams for the following system. Write the force equations. X:(t) +…

A: Free Body Diagram is the representation of forces maybe gravitational, applied or reactions and…

Q: Prob. 3: Determin the magnitude and diredan the resultant forces shown in Big 450 N 40 35 40 35 N 00

Q: Q9/ If FB = 3 kN and its angle e = 45°, determine the magnitude of the resultant force of the two…

A: Given dataForce in tug A FA = 2kNForce in tug B FB = 3kNAngle of force A with respect to x axis θA =…

Q: Q5: The forces FI-6 kN, F2- 5 kN, and F3-8 kN as shown in the Figure all of which act on point A of…

A: givenF1=6kN=6000NF2=5kN=5000NF3=8kN=8000N

Q: Q2/ Determine the resultant of the force system shown in Fig. 224 300 1 30 361 3.

Q: F= 600 N HW06-1 Determine the magnitude of the projection of force F = 600 N along the u axis. 4 m…

Q: Q 2/ the forces of these cables acting on the antenna are Fn-520 N, Fc 600 N, and Fp-560 N,…

A: The given data are: A=0,0,24B=0,-10,0C=16,18,0D=-12,8,0O=0,0,0FB=520 NFC=600 NFD=560 N

Q: The rectangular plate of sides 530 mm x 1240 mm is supported by hinges along its side BC and by the…

Q: Refering to the figure below, determine the components of force P along the x-y axes which are…

Q: Determine the magnitude of y component of the resultant force of the system of forces shown in…

A: The free body diagram of the forces is as follows:

Q: Current Attempt in Progress In checking a recently installed fencepost for adequacy of the ground…

A: GivenP=(-165i+55j+105K)

Q: Q/ Determine the magnitude of the resultant forces acting on the screw eye and its direction…

A: Resolve the forces into its components as shown in the figure. Now, ∑Fx=2cos45°-6cos60°=-1.586 kN…

Q: a. Determine the magnitude of the equivalent concentrated load and the location at which it acts to…

A: Given data: Distributed loading function, wx=2500x lbft

Q: The peg at point B holds the two ropes BA and BC which supports the outdoor canopy. Rope BA is under…

Q: H.W1:The 624 N force is a resultant of two force P & Q shown in fig. determine these forces. 624 N 3…

Q: The force R is the resultant of the forces P1, P2, and P3 acting on the rectangular plate as shown:…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: 12. Two cables are used to secure the overhang boom in position and support the 1500-N load. If the…

Q: Determine the x and y components of each of the forces shown. - 008- Dimensions in mm 800 N 600 424…

Q: Determine the magnitude of moment (Nm) of the 681-N force about point A if x = 0.4 m , y = 0.68 m,…

Q: 3. Determine the resultant of the three forces acting on the dam and locate its intersection with…

Q: II the resultant of the two forces and couple (M) ne, shown in figure(7) passes through point (0)…

Q: 08. The eyebolt supports the four forces shown. If the resultant force on the bolt is 3 kN in the…

A: Since the y-component of net force is zero,…

Q: Q2/ Determine the projections Pa and Ph of the 4-kN force F F = 4 kN on to the a- and b- axes. 30°…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Q/ Determine the magnitude of the resultant forces acting on the screw eye and its direction…

Q: För the figure shown below,dete min the components of F perpendicular and parallel to the incline. F…

Q: Q2/ Determine the resultant of the force system shown in Fig. 224 300 1 2 30° 3 361 2.

Q: Q5/ Determine the resultant of the force system of fig. And locate it with respect to point A 100N 2…

Q: The bent rod is supported at points A, B and C by smooth journal bearings, and is subjected to force…

A: Moment is known as the bending action of force which is product of magnitude of force to the…

Q: 16. If the resultant of twc equal forces has the same magnitude as either of the for gle between the…

A: given:

Question

Horizontal
P= 180 N
a) While steadily pushing the machine up on an
incline surface, a person exerts 180 N force P as
shown. Determine the components of P which are
parallel and Perpendicular to the incline surface?
10
15

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The center of gravity of the 850-N man is at G. If the man pulls on the rope with a 388-N force, determine the horizontal distance b between the man's feet and G.
B. Cords are oop around s simall spaces eparating (wo eylinders whose total weight is 375 kg as shown in figure. These cords pass over frctonless pulley o weights of 85 kg and 130 kg. Determine the angle & and the normal Force N between the cylinder the smooth surface. ‘Weight = 375 kg,
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the support force on the rear tire.
DRAW FREE BODY DIAGRAM DETERMINE THE AMOUNT OF NORMAL FORCES EXERTED ON THE CONTAINER. ANSWER IN 2 DECIMAL PLACES
The bent rod is supported at points A, B and C by smooth journal bearings, and is subjected to force F. If dimensions a = 2.3 m, b = 1.5 m, c = 0.6 m, and d = 2.5 m, and the force F is {-2i + 9j - 3k} kN, determine the magnitude of the moment (in kN⋅m) caused by force F about point A. Answer must include 2 places after the decimal point.
The wheelbarrow with a load weighs 118 kg, and its center of gravity is located at point A. (The entire weight can be considered to act at point A. Use g = 9.81 m/s².) How much vertical force F is needed to lift the wheelbarrow's handles?
A loaded scow has a draft of 1.8 m in fresh water, when upright. The scow is 6 m wide, 12 m and 2.4 m high. The center of gravity of the scow is 1.8 m above the bottom along the vertical axis of symmetry. (a) determine the initial metacentric height (b) What is the maximum single weight that can be moved transversely from the center of the unloaded scow over the side without sinking the scow. (c) If the maximum weight obtained in (6) is doubled, at what distance from the center will the scow be on the verge of submergence.
the man is holding up the 35-kg ladder ABC by pushing perpendicular to ladder. The total length of the ladder is AC=6m. If maximum force that the man can exert is 400N at B which is 2m from A. determine the smallest angle, theta, at which the man can support the ladder
Determine the force P needed to just open the 2-m wide parabolic gate, if the hinge is at thefollowing y-position in the xy-plane:Odd: H = 2 metersEven: H = 8 meters
Determine the extension (m) of the whole system shown if k1 = 14.7 N/m, k2 = 21.23 N/m, k3 = 38.22 N/m, k4 = 48.78 N/m, and k5 = 52.73 N/m and a force of 62.11 N is applied. (Use 2 decimal places for the final answer.)
Solve Prob. 8.43 assuming that the area is revolved about the y-axis.
The force F=5i+12j+4k lb is applied to the handle of the door. Determine the orthogonal component of F that is perpendicular to the plane of the door.