Include assumptions and fbd i want to see if i have them right 6.76 A successful California engineer has installed a circularhot tub in his backyard and finds that, for the typicaloperating conditions shown in the sketch, water mustbe added at a rate of 0.001 kg/s to maintain a fixedwater level in the tub. AirHot waterT= 310 KT = 290 K= 0.30wwwwwwIf the tub is well insulated on its sides and bottom and ifthe temperature of the makeup water is equal to thatof the tub water, at what rate must electrical heaterssupply energy to maintain the tub water at 310 K?

Given data as per question m˙=0.001 kg/sFor AirT∞=290 K, ϕ∞=0.3For Hot waterT=310 K

Answered: hot tub in his backyard and finds that,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
The pump shown is 75% efficient. If the pressure rise is 120 psi, calculate the required energy input in horsepower.
Water at a guage pressure of 4 kPa flows at a rate of 250 l/s in a 135° pipe bend of diameter 300 mm, find in MN the magnitude and direction of the resultant force on the bend.
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
In oasis Water Company to purify the water, it is flowing through a reducer in a horizontal pipe where the diameter is reduced from 35 cm to 25 cm. The pressure in the 35 cm pipe just upstream of the reducer is 150 kPa. The fluid has a vapor pressure of 50 kPa and a specific weight of 5 kN/m3. Neglecting frictional effects, calculate flow rate of water through this pipe in lit/s. Draw diagram neatly
Hydraulics 7. A turbine has a velocity of 6 m/s at the entrance to the draft tube and a velocity of 1,2 m/s at the exit. For the friction losses of 0.1 m and a tailwater of 5 m below the entrance to the draft tube, find the pressure head at the entrance.
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb, Calculate the horsepower required to do the pumping. The pump and its motor have an overall efficiency of 55 %. i. Determine the velocity of the water at point 2 in ft/s. ii. Assuming that the large open reservoir is open to the atmosphere as well, which of the following equations best describes the mechanical energy balance for the system? iii.The Reynolds number for the flow is?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb, Calculate the horsepower required to do the pumping. The pump and its motor have an overall efficiency of 55 %. i. What is Delta Z (Z2 - Z1) ? in ft. ii. Determine the theoretical shaft work required in foot-pound force per pound mass.. iii.Determine the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s.
A submersible pump of 80 percent efficiency is used in pumping water with flow rate,Q from a river to a pool at an elevation, h. The frictional losses is assumed with losscoefficient, K = 10. By the aid of a labelled diagram, derive an expression on thepower require to drive the pump.
A pump raises 650 tonnes of pure water a height of 55m in 6 hours. If the pump efficiency is 100%, what is the power required to drive the pump?
Provide one question and its solution involving an external flow of fluid .
7. A cylindrical pipe with water flowing downward at 0.02m ^ a / s has a top diameter of 0.08 m and boom diameter 0.04 m and the height of 1.5 m. Find the pressure difference between the pipes.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

hot tub in his backyard and finds that, for t operating conditions shown in the sketch, w be added at a rate of 0.001 kg/s to maintai water level in the tub.