how do i determine the creepage and cleareance distance for 150 kv high voltage insulator?

Q: 1. Give the temperature classification for solid insulating materials. Why is this classification…

A: It is asked to give the temperature classification for solid insulating materials. Also we need to…

Q: Identify and explain the different notational methods for describing the behavior of gases and…

A: Gates: It is an electronic circuit and has logical decisions based on applied input.

Q: kindly Briefly explain the opacity and translucency in insulators. thank you!

A: The insulators in which light can pass partially, or we can see partial through the insulators, they…

Q: the resistivity of annealed copper and aluminum?

A: copper is one of the oldest known materials. Its ductility and electrical conductivity were…

Q: 9. For high temperature applications such as few motor or generator coils with class F or…

A: As per guidelines given to us ,we can only provide the solution of one question in multiple type of…

Q: Discuss the suitability of dielectric heating for a particular application.

A: Dielectric Heating:- Dielectric Heating is an electric heating process that raises the temperature…

Q: Discuss various factors which affect breakdown of gases.

A: There are various factors which affect the breakdown of gases, some factors are listed below, 1. Gap…

Q: Justify: Mention and explain any 4 the differences between conducting and Non-conducting wires

A:

Q: What is the percentage of carbon residue? What is the importance of carbon residue?

A: 1) The carbon Residue value of fuel depends on the refinery processes employed in its manufacture.…

Q: What is the minimum trade size PVC conduit to contain 201 #12AWG TW75 Copper conductors.

A: First, determine the standard diameter of 12-AWG TW75 copper conductor from the NEC table. From the…

Q: What the need of testing insulators in the laboratory? Why insulators most likely to fail at lower…

A: Insulators are the substances that don't conduct electricity at all.

Q: What do you understand by Safety factor, puncture and Flashover of Insulator?

A: The safety factor is, Safety factor=Puncture voltageFlash over voltageFor example safety factor of…

Q: Relationship quantitatively and qualitatively. between leakage current and open circuit voltage in…

A: We show that parasitic leakage currents dominate the current voltage characteristics of organic…

Q: What are the different types of PCBs? Enumerate and explain some techniques in soldering.

A: PCB stands for printed circuit board. It is a plate consists of copper path and insulating layers…

Q: Define corrosion and also explain primary and secondary briefly explanation? step by step

A: The corrosion can be referred as the process by which the metal conductors loose their properties…

Q: Describe briefly various mechanism of breakdown in solids.

A:

Q: Calculate the current, voltage and power for 120 degree conduction periods. Calculate the current,…

A: (1)120° conduction modeRMS value of phase voltage,Vphase=Vdc6=5006=204.12 VVphase=204.12 VRMS value…

Q: Hall-effect voltages are much greater for relatively poor conductors (such as germanium) than for…

A: Hall effect- A potential difference due to a transverse electric field is created when a magnetic…

Q: 4. A company was low on copper metal and decided to use some chemical additives just this once to…

A: Conductivity of copper : conductivity is property of copper which allows to flow electric current…

Q: Can you Briefly explain any four gaseous insulating materials.??

A: All gases are more or less insulators but air is the most important insulating material which is…

Q: Why is AC source rather than DC source used in conductivity measurements

A: In the question, explain Why is AC source rather than DC source used in conductivity measurements?…

Q: terion for hydro power plant site selection.

A:

Q: Discuss the phenomenon 'treeing and tracking' in solid insulating materials under electrical stress…

A: Breakdown due to treeing: when a solid material has some impurities like gas pockets or liquid…

Q: List the minimum trade size of Type EMT for each of the following applications. Assume the use of…

A: Given, following applications Six 14 AWG ______ Six 12 AWG ______ Three 10 AWG ______ Four 8 AWG…

Q: What do you understand by Safety factor, puncture and Flashover of Insulator

A: The part section of a pin type insulator is shown in  the figure below:

Q: What are the possible limitations in measuring electrical properties in materials (e.g., conductors,…

A: Conductors are the materials having very high conductivity for example metals semiconductors are the…

Q: ). Explain the difference between an electrical conductor and an electrical insulator. (b). Give an…

A:

Q: c) Why ACSR Conductors are preferred over Copper Conductors?

A: Overhead transmission lines and transmission towers are a typical sight in rustic India. The…

Q: A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normal operating…

A:

Q: e density of carriers in the conduction and

A: NOTE- “Since you have asked multiple questions, we will solve the first question for you. If you…

Q: What causes the depletion layer?

A:

Q: Compare dry-cells, alkaline batteries and nickel-cadmium, when it comes to improvements and…

A: Given data: dry cell Alkaline batteries Nickel-cadmium

Q: Two real life examples of conduction current

A: There are two types of current in an electrical network, these are:  Conduction current…

Q: Three 10 AWG, type THW conductors are to be installed between poles on individual insulators. What…

A: The conductor installed on the poles are mostly made up of aluminium. Ampacity is the maximum…

Q: Write one paragraph describing why you think chrome has a shiny surface.

A: Most metals are shiny like chrome when you polish them. However, they usually quickly oxidize when…

Q: A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normal operating…

A:

Q: Define permeability in brief.

A: Permeability is related to the magnetic material and it states the tendency to pass the flux. It is…

Q: What is the difference between crystal and polycrystal material?

A:

Q: State the function of insulator

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: trical conductivity - c) Increase of temperature - d) Decrease

A: The conductor is types of material that allow the current to flow into it. They are basically…

Q: Discuss the desirable properties of insulators. Explain the causes of insulator failure due to…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: 1-Identify and Explain with neat sketch of the a).Shackle Insulator   2-What do you understand by…

A: 1-a. Shackle Insulators These insulators are those insulators that are used whenever there is low…

Q: Compare between Mono, poly and thin film with respect to shading effect, temperature effect ,…

A: To analyse the given statement

Types of Charge Carriers

A carrier is a type of object which carries a particular thing from one point to another point. For instance, people use different vehicles from one place to another, and the vehicle carries those people and acts as a carrier.