how long will it take to charge a 1000μF capacitor through 1 KQ resistor tofull 16V source voltage? d) forevera) 1000 microsecondsb) 10secondsc) one dayd)foreverWhat maximum voltage can be safely applied to series resistors, 1.2 KQ ¹4 Wand 680 0%W?a) 9.81Vb) 17.32. Vc)27.07 Vd) 32.52VWhen a capacitor is being charged from a 12V power source, the currentflowing through thecapacitor willa} increaseb} decreasec) remain the samed) can't be determinedCalculate the voltmeter reading in the circuit shown in the figure when wiperarm of the potentiometer is set at 25% up fromthe bottom. note: theresistance value is 3.3 Kilo-ohms.9VOa) 2.13 Vb) 3.12 Vc)2.31 Vd) 6.25 V1k3k3

Since you have posted the multiple questions so we are supposed to answer the 1st one.

Answered: how long will it take to charge a…

how long will it take to charge a 1000μF capacitor through 1 KQ resistor to full 16V source voltage? d) forever a) 1000 microseconds Ob) 10seconds c) one day O d) forever

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Choose the correct option and explain... In order to connect a LED to one of the pins a)You need to…

A: Answer: a)You need to define that LED as an OUTPUT in the setup function Explanation: a. The setup…

Q: 2 F(S) = (35-2) (25-1) (35+2)

Q: Write KCL equation for the current at node a in the circuit shown below. 1₁ R1 R3 a 13 12 www R2

A: Given circuit:

Q: If the modulation rate of a noise is 30 Hz, how much of a change in amplitude (what AM depth) will…

A: Given: modulation rate (M) of a noise = 30 Hz we have to find out the change in AM depth required…

Q: In a DC machine, rectification process is carried out in order to get unidirectional output (DC).…

A: The correct option along with the explanation is provided in the following section.

Q: A 4.16 kV, 3-ph industrial plant bus is supplied from the utility mains. Connected to the 4.16 kV…

A: 0.51 Given data, For induction motor, Pm = 1750 HP Load = 80% full load Pf = 0.86 lagging For…

Q: Find Zah, (Z-Thevenin) for the following circ 50/30° V j20 12 m 1052 wwa -1022

A: Given data, Circuit diagram is given as,

Q: Which memory storage is widely used in PCs and Embedded Systems?

A: The correct option along with the explanation is provided in the following section.

Q: A 110-V shunt generator has a full load current of 100 A, shunt field resistance of 55 Ω and…

Q: Question 2: Refer to the Figure 2 below. Determine the following parameters shown on the table given…

A: Given, Volt/div is equal to 500 mV. Time per division is 500 μsec/div

Q: Given the signal below with a height of 12 V and a pulse width T/2. Find the first three…

A: The periodic or non periodic signal is represented in sinusoidal form by Fourier series. The Fourier…

Q: Consider the AM modulated waveform shown below: Find the modulating signal frequency, and the…

Q: a) A 2hp, 8-pole, 30 induction motor is connected to a 60 Hz power supply. From this motor, find; i)…

Q: What is true about the current through each resistor in the circuit below? If the resistances are…

Q: 14.3.4 - What signal is sent in period 9 if a slave on the 12C bus has the same slave address as was…

A: The address of the slave with which the master communicates is sent by the master to every slave…

Q: B) Show that the system shown in Figure (3) is equivalent to

Q: A sinusoidal voltage wave form of peak voltage í V and frequency f = 60Hz is applied to a bridge…

A: Given a sinusoidal wave form with, Peak voltage, Vm=π V Frequency, fin=60 Hz Applied to bridge…

Q: Find the load impedance ZL that would absorb the maximum power. 152-10° V rms 00 OLCHAR +- 2415°…

Q: The two equal charges Q₁ = 5 µC and Q₂ = 1 μC are seperated by 50 cm, are kept in a vacuum. Find the…

A: We have two equal charges as shown in figure, Q1 = 5 μC = 5 * 10-6 C Q2 = 1 μC = 1 * 10-6 C d = 50…

Q: In a specific multiplexer, 4 select lines are present. Estimate the number of inputs present in the…

Q: The maximum and minimum stresses in the dielectric of a single-core cable are 40 kV/cm (r.m.s.) and…

A: Given, In the dielectric of a single core cable, Maximum stress, gmax=40 kVcm Minimum stress,…

Q: A non-sinusoidal voltage consists of a fundamental and a third harmonic. If the effective value of…

Q: (1) Determine the output voltage of the DAC (digital-to-analog converter) if the input is…

Q: A 3-phase hydroelectric synchronous generator is rated 110 MW, 0.8 pf lagging, 13.6 kV, A-connected,…

A: We have an 3-phase hydroelectric synchronous generator with, Rating of generator = 110 MW Power…

Q: A load absorbs S = 100 kVA at a leading power factor of pf = 0.72. Use this information to calculate…

Q: A load consists of XL=30 Q and Xc=120 Q are connected in parallel across 120 Volt supply. The…

A: Given, A load consists XL and Xc connected in parallel Inductive reactance, XL=j30 Ω Capacitive…

Q: Let A = -5 +j 9, B = 2 +j 9, and C = -7 +j -7. Find: (a) C-B (b) 2A-3B + 5C

A: It is given that: A=-5+j9B=2+j9C=-7+j-7=-7-j7

Q: 8a. Using Kirchhoff's rules, calculate the current I₁ in resistor R₁, using the directions indicated…

Q: 0 2230 + 5490 v(e) U (P)? 2 0 240° ] 16-20° 3/45° 1690° (2+3690) J T10L0"

Q: (a) Describe the following metrology terms: i. Accuracy ii. Uncertainty iii. Calibration iv.…

Q: For the given circuit, find voltage V using Superposition theorem. 85 15V4 12 reell +f 1022 2052…

Q: Develop the graph of the network shown infigure given obtain the (i) incidence matrix. (ii) reduced…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: A balanced abc sequence source Vab= 400230° volt is connected to a star- connected (four wires)…

Q: Show that the two systems shown in Figure (1) are equivalent. Depend on your study, what is this…

A: Given:

Q: A conducting disc 20 cm in diameter pivoted by a vertical spindle which is lying in uniform vertical…

A: Given: The diameter of the disc is 20 cm The flux density is 0.3 T The current is 15 mA

Q: QUESTION 3 Which of the following equations describes the relationship between the input, output,…

Q: Kindly give the copy solution. Typing is hard to understand

Q: Question 8.a Which article of the NEC describes the proper placement of outlets in this type of…

A: The Given is article of the NEC describes the proper placement of outlets in this type of room.

Q: (b) Find the inverse Fourier transform of the following: 2 sin 5@ (i) √2π.w

A: Given: Fourier transform X(jw)=2sin5ω2πω We have to compute inverse Fourier transform of the above…

Q: Draw the logic circuit for the simplified expression a) and b)

Q: 3. What is the total current for a circuit with a voltage in the source equals 15 V and three…

A: Given :- Voltage source, VS = 15 V Resistance of the circuits, R1 = 4 ohm R2 = 5 ohm ,…

Q: In a certain transistor, the emitter current is 1.5 times larger as the collector current. If the…

A: Given, In a certain transistor, emitter current is 1.5 times of the collector current. IE=1.5IC…

Q: A current of 8.2 A is maintained in a single circular loop having a circumference of 80 cm. An…

A: Given data, Number of loop N =1 Current flowing I=8.2 A Circumference 2πr=80 cm Magnetic field B=2…

Q: A Y-connected generator rated at 300MVA, 33kV, has a reactance of 1.24 p.u. Find the ohmic value of…

A: Given: A Y-connected generator rated at 300 MVA, 33 kV. Base values, S=300 MVAV=33 kV Reactance,…

Q: b) From a single-phase half-wave rectifier circuit, demonstrate on how the DC outp voltage being…

Q: Which of the following elements of electrical engineering cannot be analyzed using Ohm's law? a)…

A: The correct option along with the explanation is provided in the following section.

Q: Find the size of the C-filter in an FWR needed to keep ripple values within 3%; the circuit is…

Q: Explain the function of each block in the following figure. Draw timing diagram to show how the…

A: The given diagram consists of: DAC An operational amplifier in a Non-inverting configuration…

Q: Using Karnaugh map, simplify the expression F(W, X, Y, Z) = Σm(0, 1, 2, 4, 5, 6, 8, 9, 12, 13, 14).…

Q: Explain the principles of servomotors and discuss their different types.

A: Servomotor: The basic principle of servo motor is based on Pulse Width Modulation (PWM) concept, in…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

how long will it take to charge a 1000μF capacitor through 1 KQ resistor to
full 16V source voltage? d) forever
a) 1000 microseconds
b) 10seconds
c) one day
d)
forever
What maximum voltage can be safely applied to series resistors, 1.2 KQ ¹4 W
and 680 0%W?
a) 9.81V
b) 17.32. V
c)27.07 V
d) 32.52V
When a capacitor is being charged from a 12V power source, the current
flowing through thecapacitor will
a} increase
b} decrease
c) remain the same
d) can't be determined
Calculate the voltmeter reading in the circuit shown in the figure when wiper
arm of the potentiometer is set at 25% up fromthe bottom. note: the
resistance value is 3.3 Kilo-ohms.
9V
Oa) 2.13 V
b) 3.12 V
c)2.31 V
d) 6.25 V
1k
3k3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(6) A battery pack of 30 nickel metal hydride battery modules powers a high performance electric vehicle. Each module has an open circuit voltage of 13 V and an effective resistance of 10 mohm for a 10 second acceleration pulse. What is the peak power capability of this battery pack using the USABC definition (peak power = 2/9 x Voc2/R where Voc is the open circuit voltage and R is the resistance)A. 75 kWB. 113 kWC. 338 kWD. 507 kW
An electric radiator is required to dissipate 1kW when connected to a 230V supply. If the coils of the radiator are of wire 0.5mm in diameter having resistivity of 60 michro olms cm, calculate the neccesary length of the wire.
Design a solar PV panel that can deliver 400W at 38V from a cross-sectional area of 12 square centimetres if the PV cell voltage is 0.7V the current density is 180A per metre square.
Estimate the dielectric losses in the solid specimen subjected to an alternating field of 40KV/cm, has an absolute permittivity of 4.445 x10-11 and the loss angle of that solid dielectric material is 0.28647at Oman power frequency. And also the same specimen while subjected to 3 KV/cm DC supply with the resistance value of 10 Mega Ohm, then determine the heat generated in the specimen.
If the dark saturation current of a solar cell is 1.7X10-8 A/m2, the cell temperature is 27 oC, and the short-circuit current density is 250 A/m2, Vmax = 0.526 V, calculate the open-circuit voltage, Voc; current density at maximum power, Imax.
If the dark saturation current of a solar cell is 1.7X10-8 A/m2, the cell temperature is 27 oC, and the short-circuit current density is 250 A/m2, Vmax = 0.526 V, calculate the maximum power, Pmax; and maximum efficiency, ηmax. when the available solar radiation is 820 W/m2
A single energy meter has a meter constant of 200rev/kwh. When supplying a non-inductive load of 4.4 A at normal voltage, the meter takes 3 minutes for 10 revolutions. Find the percentage error
A barangay power station supplies 60kW to a load over 2,500ft, 100 mm², two conductors copper feeder. The resistance of which is 0.0078 ohm per 1,000 ft the bus bar voltage is maintained constant at 600V. Determine the load current.
Under insolation conditions of 500 W/m2 (direct sunlight), and 10% solar cell efficiency (defined as the ratio of electrical output power to incident solar power), calculate the area required for a photovoltaic (solar cell) array capable of running the above vehicle at half power. Note: The vehicle is driven by a motor of 40 hp.
A solar panel has a surface area of 0.5 m^2 and delivers maximum power at 2.5A, 19 V when in sunlight with incident radiation of 95 mW/cm^2. If the open circuit voltage is 25 V and the short circuit current is 3 A, calculate:(a) the power generated by the panel,(b) the fill factor, and(c) the efficiency of the panel. (d) Given that the solar panel is exposed to sunlight 6.5 hours per day (on average) and the energy used to manufacture the solar panel is 890 kWh/m^2, calculate the energy payback time of the solar panel.
An office has a following dimensions : length = 20 m. width = 10 m. 1.) Ceiling to desk height is 2 m. 2.) Area to be illuminated to a general is 250 lux using twin lamp 32 watt CFLLuminaire with a SHR of 1.25. 3.) Each lamp has an initial output of 85 lumen per watt. 4.) Maintenance factor is 0.63, Utilisation factor is 0.69 Design a lighting system for this office by computing the following : 1. ROOM INDEX 2. INITIAL BARE LAMP FLUX
The construction of PV solar cells uses a number of critical elements. One is indium an ingredient of the transparent conducting coating on the surface of the cell. The average material intensity for indium in solar cells is approximately 0.05 kg/kWnom. Calculate the quantity of indium that would be required for a project that would provide PV solar power with capacity factor of 0.25, sufficient to meet one third of the present needs of the US, population 301 million, each using an average of 10.2 kW. The current world production of Indium is 600 tones per year. If the solar project were to be implemented over a 5 year time span, is it true that the supply of indium be adequate?